wire mesh manufacturers in pune

Stainless Steel 446 Wire Mesh Manufacturers In India

Sachiya Steel International is one of the Leading Manufacturer And Exporter Of High Quality Stainless Steel 446 Wire Mesh, which is the most widely used of all stainless steel alloys. Stainless Steel 446 Hexagonal Wire Mesh is typically used in the annealed condition, at service temperatures through 750 Degree F, however, it may be heat treated for high strength. SS 446 Welding Wire Mesh is welded with matching or with filler wire, where hardenability is limited and sections over one inch may not develop full properties.

SS 446 Netting Wire Mesh is annealed up to 1300 Degree F – 1450 Degree F for two hours, and the air cool. Recrystallization anneal these Stainless Steel 446 Woven Wire Mesh for better ductility and fatigue strength, along with heat with temperature of 1750 Degree F for two hours, and then furnace cool. For maximum fracture toughness and SCC resistance, anneal this SS 446 Spring Steel Wire Mesh up to 1950 Degree F for 1-2 hours, and then water quench.

Stainless Steel 446 Wire Mesh

Age treatment this Stainless Steel 446 Fencing Wire Mesh up to 1150 Degree F – 1300 Degree F for two to four hours, and then air cool. For increased fracture toughness, but lower tensile strength of 446 Stainless Steel Wire Mesh precipitation treat (overage) 1150 Degree – 1250 Degree F for four hours, and then air cool. Stress relief annealing this SS 446 Wire Mesh is commonly 1000 Degree F – 1200 Degree F for one to four hours, and then air cool.

SS 446 Wire mesh Specifications

Specifications : ASTM A 164 ASME SA 164
Standard : ASTM, ASME International Standards
Length : 30m to 100″
Width : 1m to 48″
Type : Wire Mesh , Hexagonal Wire mesh, Welding Wire mesh, Netting Wire mesh, Woven Wire mesh , Spring Steel wire mesh, Fencing Wire mesh etc.

446 Stainless Steel Wire Mesh Chemical Composition

Grade C Mn Si P S Cr MO Ni N
446 min. 23.0 0.10
max. 0.20 1.5 0.75 0.040 0.030 30.0 0.50 0.25

Stainless Steel 446 Wire mesh Mechanical Properties

Grade Tensile Strength (MPa) min Yield Strength 0.2% Proof (MPa) min Elongation (% in 50mm) min Hardness
Rockwell B (HR B) max Brinell (HB) max
446 485 275 20 92 201

Equivalent Grades for 446 Stainless Steel Wire mesh

STANDARD WERKSTOFF NR. UNS JIS BS GOST AFNOR EN
SS 446 1.4762 S44600 SUS 446

SS 446 Wire Mesh Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

446 Steel Wire mesh Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2023-12-22T11:23:13+05:30December 9th, 2021|

Stainless Steel 410 Wire Mesh Manufacturers In India

Sachiya Steel International is one of the Leading Manufacturer And Exporter Of High Quality Stainless Steel 410 Wire Mesh, which have austenite as their primary phase (face centered cubic crystal). SS 410 Hexagonal Wire Mesh is used for a variety of applications where good corrosion and outstanding hardness is necessary. Stainless Steel 410 Welding Wire Mesh also offers higher creep, stress to rupture and tensile strength at elevated temperatures, in addition to excellent corrosion resistance and strength properties.

Stainless Steel 410 Netting Wire Mesh contains chromium and nickel (sometimes manganese and nitrogen), structured around the composition of iron, 18 % chromium, and 8 % nickel. Austenitic SS 410 Woven Wire Mesh are not harden able by heat treatment, which further refer to the lower carbon content to allow for greater corrosion protection when welding. Stainless Steel 410 Spring Steel Wire Mesh is austenitic steel containing 18 % – 20% chromium and 8 % – 10% nickel.

Stainless Steel 410 Wire Mesh

SS 410 Fencing Wire Mesh is not subject to embrittlement or loss of corrosion resistance in the heat – affected zones that affects many other straight chromium alloys. 410 Stainless Steel Wire Mesh is especially valuable for applications requiring high – temperature scaling resistance and for those applications where it gives only marginal protection. SS 410 Wire Mesh is not usually used at temperatures exceeding 800 Degree F (427 Degree C) due to quick hardening and loss of corrosion resistance.

SS 410 Wire mesh Specifications

Specifications : ASTM A 164 ASME SA 164
Standard : ASTM, AISI International Standards
Length : 30m to 100″
Width : 1m to 48″
Type : Wire Mesh , Hexagonal Wire mesh, Welding Wire mesh, Netting Wire mesh, Woven Wire mesh , Spring Steel wire mesh, Fencing Wire mesh etc.

410 Stainless Steel Wire Mesh Chemical Composition

Grade C Mn Si P S Cr Mo Ni N
410 min. 11.5
max. 0.15 1.0 1.00 0.040 0.030 13.5 0.75

Stainless Steel 410 Wire mesh Mechanical Properties

Grade Tensile Strength (MPa) min Yield Strength 0.2% Proof (MPa) min Elongation (% in 50mm) min Hardness
Rockwell B (HR B) max Brinell (HB) max
410 480 275 16 95 201

Equivalent Grades for 410 Stainless Steel Wire mesh

Grade UNS No Old British Euronorm Swedish SS Japanese JIS
BS En No Name
410 S41000 410S21 56A 1.4006 X12Cr13 2302 SUS 410

SS 410 Wire Mesh Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

410 Steel Wire mesh Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2023-12-25T15:35:53+05:30December 8th, 2021|

Stainless Steel 347H Wire Mesh Manufacturers In India

Sachiya Steel International is one of the Leading Manufacturer And Exporter Of High Quality Stainless Steel 347H Wire Mesh, which cannot be hardened by heat treatment but can be strengthened by cold working. With over 11 % of chromium, SS 347H Hexagonal Wire Mesh is about 200 times more resistant to corrosion than mild steel. Stainless Steel 347H Welding Wire Mesh contain trace amounts of nickel, 12 % – 17 % chromium, less than 0.1 % carbon, along with other alloying elements, such as molybdenum, Aluminium or titanium. These magnetic and heat – treatable SS 347H Netting Wire Mesh are used in knives, cutting tools, as well as dental and surgical equipment.

Our prime aim is to manufacture best quality of Stainless Steel 347H Woven Wire Mesh, along with ingots and forging ingot (alloy & non alloy) to suit the industrial need. We use fine quality of raw materials and scrap for our production of SS 347H Spring Steel Wire Mesh. Our adaptation to new technological inputs and multifaceted infra structural base would ensure quality Stainless Steel 347H Fencing Wire Mesh.

Stainless Steel 347H Wire Mesh

The process of manufacturing 347H Stainless Steel Wire Mesh from raw materials such as scrap and sponge iron involves many sophisticated processes. SS 347H Wire Mesh will have a structure consisting fine materials which, as the Carbon content is raised, transitions to a fully structure and on to one containing free carbide in a matrix of fine materials and even some for the highest Carbon grades.

SS 347H Wire mesh Specifications

Specifications : ASTM A 164 ASME SA 164
Standard : ASTM, AISI International Standards
Length : 30m to 100″
Width : 1m to 48″
Type : Wire Mesh , Hexagonal Wire mesh, Welding Wire mesh, Netting Wire mesh, Woven Wire mesh , Spring Steel wire mesh, Fencing Wire mesh etc.

347H Stainless Steel Wire Mesh Chemical Composition

Grade C Mn Si P S Cr Cb Ni Fe
SS 347H 0.04 – 0.10 2.0 max 1.0 max 0.045 max 0.030 max 17.00 – 20.00 8xC – 1.10 9.00 – 13.00 63.72 min

Stainless Steel 347H Wire mesh Mechanical Properties

Density Melting Point Tensile Strength Yield Strength (0.2%Offset) Elongation
8.0 g/cm3 1454 °C (2650 °F) Psi – 75000 , MPa – 515 Psi – 30000 , MPa – 205 35 %

Equivalent Grades for 347H Stainless Steel Wire mesh

STANDARD WERKSTOFF NR. UNS JIS BS GOST AFNOR EN
SS 347H 1.4961 S34709 SUS 347H X6CrNiNb18-12

SS 347H Wire Mesh Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

347H Steel Wire mesh Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2023-12-26T15:31:40+05:30December 8th, 2021|

Stainless Steel 347 Wire Mesh Manufacturers In India

Sachiya Steel International is one of the Leading Manufacturer And Exporter Of High Quality Stainless Steel 347 Wire Mesh, which contains 18 percent of chromium and 8 percent of nickel. In principle, heat – treating already takes place when our Stainless Steel 347 Hexagonal Wire Mesh is hot – rolled at a particular temperature and cooled afterward at a certain rate, but there are as well many heat – treating process facilities specifically designed to produce particular microstructures and properties. By varying the ratio of oxygen and argon in this Stainless Steel 347 Welding Wire Mesh, it is possible to remove carbon to controlled levels by oxidizing it to carbon monoxide without also oxidizing and losing expensive chromium.

Our SS 347 Netting Wire Mesh is not harden able by heat treatment and is nonmagnetic. Typical applications of our Stainless Steel 347 Woven Wire Mesh include aircraft and the dairy and food – processing industries. This Stainless Steel 347 Spring Steel Wire Mesh contains 10.5 percent to 27 percent chromium and is nickel – free; because of their low carbon content.

Stainless Steel 347 Wire Mesh

Our SS 347 Fencing Wire Mesh are not harden able by heat treatment and have less critical anticorrosion applications, such as architectural and auto trim. After solidifying this SS 347 Wire Mesh, the ingot was stripped from the mould, reheated, and then reduced in size by hot – rolling in a primary (blooming) mill to give billets in section.

SS 347 Wire mesh Specifications

Specifications : ASTM A 164 ASME SA 164
Standard : ASTM, AISI International Standards
Length : 30m to 100″
Width : 1m to 48″
Type : Wire Mesh , Hexagonal Wire mesh, Welding Wire mesh, Netting Wire mesh, Woven Wire mesh , Spring Steel wire mesh, Fencing Wire mesh etc.

347 Stainless Steel Wire Mesh Chemical Composition

Grade C Mn Si P S Cr Mo Ni N
347 min. 17.0 9.0
max. 0.08 2.0 1.0 0.040 0.030 20.0 13.0

Stainless Steel 347 Wire mesh Mechanical Properties

Grade Tensile Strength (MPa) min Yield Strength 0.2% Proof (MPa) min Elongation (% in 50mm) min Hardness
Rockwell B (HR B) max Brinell (HB) max
347 515 205 40 92 201

Equivalent Grades for 347 Stainless Steel Wire mesh

STANDARD WERKSTOFF NR. UNS JIS BS GOST AFNOR EN
SS 347 1.4550 S34700 SUS 347 08Ch18N12B X6CrNiNb18-10

SS 347 Wire Mesh Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

347 Steel Wire mesh Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2023-12-27T12:41:06+05:30December 7th, 2021|

Stainless Steel 321 Wire Mesh Manufacturers In India

Sachiya Steel International is one of the Leading Manufacturer And Exporter Of High Quality Stainless Steel 321 Wire Mesh, which improves the elevated temperature properties of the alloy. The increased addition of carbon in Stainless Steel 321 Wire Mesh allows for a greater creep resistance and higher strength performance in elevated temperature environments (above 530°C). Stainless Steel 321H Wire Mesh may be susceptible to chloride stress cracking and excellent weldability in field.

For cleaning the surface of Stainless Steel 321 Hexagonal Wire Mesh, the processes brushing, grinding, pickling or blasting (iron-free silica sand or glass spheres) can be applied. Stainless Steel 321H Welding Wire Mesh responds well to hardening by cold working and has good welding characteristics. Stainless Steel 321 Netting Wire Mesh is the grade of choice for applications in the temperature range of up to about 900°C, combining high strength, resistance to scaling and phase stability with resistance to subsequent aqueous corrosion.

Stainless Steel 321 Wire Mesh

The resultant austenitic structure of Stainless Steel 321H Woven Wire Mesh at room temperature has optimum corrosion resistance containing as it does all of the chromium in solution. This titanium addition in Stainless Steel 321 Spring Steel Wire Mesh reduces or prevents carbide precipitation during welding and in 800 – 1500 °F (427 – 816 °C) service. Stainless Steel 321H Fencing Wire Mesh has good oxidation resistance in intermittent service to 900 °C and in continuous service to 925 °C.

SS 321/321H Wire mesh Specifications

Specifications : ASTM A 164 ASME SA 164
Standard : DIN, ASTM, BS and all International Standards
Length : 30m to 100″
Width : 1m to 48″
Type : Wire Mesh , Hexagonal Wire mesh, Welding Wire mesh, Netting Wire mesh, Woven Wire mesh , Spring Steel wire mesh, Fencing Wire mesh etc.

321/321H Stainless Steel Wire Mesh Chemical Composition

Grade C Mn Si P S Cr N Ni Ti
SS 321 0.08 max 2.0 max 1.0 max 0.045 max 0.030 max 17.00 – 19.00 0.10 max 9.00 – 12.00 5(C+N) – 0.70 max
SS 321H 0.04 – 0.10 2.0 max 1.0 max 0.045 max 0.030 max 17.00 – 19.00 0.10 max 9.00 – 12.00 4(C+N) – 0.70 max

Stainless Steel 321/321H Wire mesh Mechanical Properties

Density Melting Point Tensile Strength Yield Strength (0.2%Offset) Elongation
8.0 g/cm3 1457 °C (2650 °F) Psi – 75000 , MPa – 515 Psi – 30000 , MPa – 205 35 %

Equivalent Grades for 321/321H Stainless Steel Wire mesh

STANDARD WERKSTOFF NR. UNS JIS EN
SS 321 1.4541 S32100 SUS 321 X6CrNiTi18-10
SS 321H 1.4878 S32109 SUS 321H X12CrNiTi18-9

SS 321/321H Wire Mesh Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

321/321H Steel Wire mesh Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2023-12-28T18:40:22+05:30December 7th, 2021|

Stainless Steel 317L Wire Mesh Manufacturers In India

Sachiya Steel International is one of the Leading Manufacturer And Exporter Of High Quality Stainless Steel 317L Wire Mesh, which is one of the most sustainable material choices available to decision makers. The work – hardening property of austenitic SS 317L Hexagonal Wire Mesh, that results in a significant strengthening of the material from cold – working alone, and the high strength allow reduced material thickness over conventional grades, therefore cost savings. Modern steel – making techniques mean that Stainless Steel 317L Welding Wire Mesh can be cut, welded, formed, machined, and fabricated as readily as traditional steels.

SS 317L Netting Wire Mesh has good strength and good resistance to corrosion and oxidation at elevated temperatures. Stainless Steel 317L Woven Wire Mesh is used at temperatures up to 1700 Degree F and up to 2000 Degree F for the high temperature stainless grade. SS 317L Spring Steel Wire Mesh is used extensively in heat exchangers, super – heaters, boilers, feed water heaters, valves and main steam lines as well as aircraft and aerospace applications.

Stainless Steel 317L Wire Mesh

With time and temperature, changes in metallurgical structure of Stainless Steel 317L Fencing Wire Mesh can be expected with any metal. In 317L Stainless Steel Wire Mesh, the changes can be softening, carbide precipitation, or embrittlement. Softening or loss of strength occurs in SS 317L Wire Mesh at about 1000 Degree F and at about 900 Degree F for the harden able series and 800 Degree F for the non – harden able series.

SS 317L Wire mesh Specifications

Specifications : ASTM A 164 ASME SA 164
Standard : ASTM, AISI International Standards
Length : 30m to 100″
Width : 1m to 48″
Type : Wire Mesh , Hexagonal Wire mesh, Welding Wire mesh, Netting Wire mesh, Woven Wire mesh , Spring Steel wire mesh, Fencing Wire mesh etc.

317L Stainless Steel Wire Mesh Chemical Composition

Grade C Mn Si P S Cr Mo Ni Fe
SS 317L 0.035 max 2 max 1.00 max 0.045 max 0.030 max 18.00 – 20.00 3.00 – 4.00 11.00 – 15.00 57.89 min

Stainless Steel 317L Wire mesh Mechanical Properties

Density Melting Point Tensile Strength Yield Strength (0.2%Offset) Elongation
7.9 g/cm3 1400 °C (2550 °F) Psi – 75000 , MPa – 515 Psi – 30000 , MPa – 205 35 %

Equivalent Grades for 317L Stainless Steel Wire mesh

STANDARD WERKSTOFF NR. UNS JIS BS GOST AFNOR EN
SS 317L 1.4438 S31703 SUS 317L X2CrNiMo18-15-4

SS 317L Wire Mesh Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

317L Steel Wire mesh Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2024-02-05T12:10:34+05:30December 6th, 2021|Wire Mesh|

Stainless Steel 317 Wire Mesh Manufacturers In India

Sachiya Steel International is one of the Leading Manufacturer And Exporter Of High Quality Stainless Steel 317 Wire Mesh, which is used to avoid corrosion problems caused by welding. SS 317 Hexagonal Wire Mesh exhibits great resistance to chloride pitting and crevice corrosion because of high molybdenum content and nitrogen additions, and the higher nickel content ensures better resistance to stress – corrosion cracking versus the 300 series. The higher alloy content of super austenitic SS 317 Welding Wire Mesh makes them more expensive. Stainless Steel 317 Netting Wire Mesh is used in pressure vessels but is a low – alloy carbon steel with a chromium content of 0.5 % to 9 %.

Stainless Steel 317 Woven Wire Mesh is preferred where biocompatibility is required (such as body implants and piercings). Stainless Steel 317 Spring Steel Wire Mesh reduces the sensitization effect (precipitation of chromium carbides at grain boundaries) caused by the high temperatures involved in welding. SS 317 Fencing Wire Mesh generally has better engineering properties than austenitic grades, but has reduced corrosion resistance, because of the lower chromium and nickel content.

Stainless Steel 317 Wire Mesh

317 Stainless Steel Wire Mesh are also usually less expensive, which can offer similar performance at lower cost and are preferred in certain applications. SS 317 Wire Mesh have a body – centered cubic crystal system and contain between 10.5 % and 27 % chromium with very little nickel, if any, but some types can contain lead.

SS 317 Wire mesh Specifications

Specifications : ASTM A 164 ASME SA 164
Standard : DIN, ASTM, BS and all International Standards
Length : 30m to 100″
Width : 1m to 48″
Type : Wire Mesh , Hexagonal Wire mesh, Welding Wire mesh, Netting Wire mesh, Woven Wire mesh , Spring Steel wire mesh, Fencing Wire mesh etc.

317 Stainless Steel Wire Mesh Chemical Composition

Grade C Mn Si P S Cr Mo Ni N
SS 317 0.08 max 2 max 1.0max 0.045 max 0.030 max 18 – 20 3.0-4.0 11.0-15.0 57.845 min

Stainless Steel 317 Wire mesh Mechanical Properties

Density Melting Point Tensile Strength Yield Strength (0.2%Offset) Elongation
7.9 g/cm3 1400 °C (2550 °F) Psi – 75000 , MPa – 515 Psi – 30000 , MPa – 205 35 %

Equivalent Grades for 317 Stainless Steel Wire mesh

STANDARD WERKSTOFF NR. UNS JIS BS GOST AFNOR EN
SS 317 1.4449 S31700 SUS 317

SS 317 Wire Mesh Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

317 Steel Wire mesh Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2024-02-07T11:12:16+05:30December 6th, 2021|Wire Mesh|

Stainless Steel 316Ti Wire Mesh Manufacturers In India

Sachiya Steel International is one of the Leading Manufacturer And Exporter Of High Quality Stainless Steel 316Ti Wire Mesh, which makes up approximately 30 % of its composition, with iron being found in equal if not greater amounts. Our Stainless Steel 316Ti Hexagonal Wire Mesh provides corrosion resistance, and specifically resistance from chloride stress cracking. This SS 316Ti Welding Wire Mesh is practically immune to chlorine and was designed to be used in sulfuric environments.

Our Stainless Steel 316Ti Netting Wire Mesh is commonly applied in acidic and / or corrosive environments, such as those that contain phosphoric and nitric acid. This Stainless Steel 316Ti Woven Wire Mesh has proven to be excellent under corrosive conditions and various forms of media. As a result, our SS 316Ti Spring Steel Wire Mesh is commonly found in processing applications — such as food or chemicals — along with pharmaceutical storage and processing. This Stainless Steel 316Ti Fencing Wire Mesh is pliable under both hot and cold working practices; however it does have some limitations in regards to temperature.

Stainless Steel 316Ti Wire Mesh

Hot – working practices in our SS 316Ti Wire Mesh should stay between 2100 Degree F — 2250 Degree F. Temperature control in 316Ti SS Wire Mesh is essential in terms of work – hardening, forging and welding the metal due to potential risks to its stability. Overall, our Grade 316Ti Wire Mesh is an excellent alternative to more expensive metals with similar applications.

SS 316TI Wire mesh Specifications

Specifications : ASTM A 164 ASME SA 164
Standard : ASTM, AISI International Standards
Length : 30m to 100″
Width : 1m to 48″
Type : Wire Mesh , Hexagonal Wire mesh, Welding Wire mesh, Netting Wire mesh, Woven Wire mesh , Spring Steel wire mesh, Fencing Wire mesh etc.

316TI Stainless Steel Wire Mesh Chemical Composition

Grade C Mn Si P S Cr Mo Ni N
SS 316Ti 0.08 max 2 max 0.75 max 0.045 max 0.030 max 16.00 – 18.00 2.00 – 3.00 10.00 – 14.00 68.395 min

Stainless Steel 316TI Wire mesh Mechanical Properties

Density Melting Point Tensile Strength Yield Strength (0.2%Offset) Elongation
8.0 g/cm3 1399 °C (2550 °F) Psi – 75000 , MPa – 515 Psi – 30000 , MPa – 205 35 %

Equivalent Grades for 316TI Stainless Steel Wire mesh

STANDARD WERKSTOFF NR. UNS JIS BS GOST AFNOR EN
SS 316Ti 1.4571 S31635 SUS 316Ti 320S31 08Ch17N13M2T Z6CNDT17‐123 X6CrNiMoTi17-12-2

SS 316TI Wire Mesh Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

316TI Steel Wire mesh Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2024-01-04T15:38:11+05:30December 4th, 2021|

Stainless Steel 316 Wire Mesh Manufacturers In India

Sachiya Steel International is one of the Leading Manufacturer And Exporter Of High Quality Stainless Steel 316 Wire Mesh, which is a relatively rare form of corrosion which requires a very specific combination of tensile stress, temperature and corrosive species, often the chloride ion, for it to occur. Typical applications where SCC can occur in Stainless Steel 316 Hexagonal Wire Mesh are hot water tanks and swimming pools. Another form known as sulphide stress corrosion cracking (SSCC) in Stainless Steel 316L Welding Wire Mesh is associated with hydrogen sulphide in oil and gas exploration and production.

Stainless Steel 316 Wire Mesh

This is now quite a rare form of corrosion, where if the Carbon level in SS 316 Netting Wire Mesh is too high, Chromium can combine with Carbon to form Chromium Carbide. This occurs at temperatures between about 450 Degree C – 850 Degree C in Stainless Steel 316L Woven Wire Mesh, where this process is also called sensitization and typically occurs during welding. The Chromium available to form the passive layer in SS 316 Spring Steel Wire Mesh is effectively reduced and corrosion can occur.

SS 316L Fencing Wire Mesh is avoided by choosing a low carbon grade the so-called ‘L’ grades or by using steel with Titanium or Niobium which preferentially combines by means of Carbon. Stainless Steel 316 Wire Mesh is rather like a battery and can accelerate corrosion of the less ‘noble’ metal.

SS 316/316L Wire mesh Specifications

Specifications : ASTM A 164 ASME SA 164
Standard : ASTM, ASME International Standards
Length : 30m to 100″
Width : 1m to 48″
Type : Wire Mesh , Hexagonal Wire mesh, Welding Wire mesh, Netting Wire mesh, Woven Wire mesh , Spring Steel wire mesh, Fencing Wire mesh etc.

316/316L Stainless Steel Wire Mesh Chemical Composition

Grade C Mn Si P S Cr Mo Ni N
316 min. 16.0 2.0-3.0 10.0
max. 0.035 2.0 0.75 0.045 0.030 18.0 14.0
316L min. 16.0 2.0-3.0 10.0
max. 0.035 2.0 0.75 0.045 0.030 18.0 14.0

Stainless Steel 316L Wire mesh Mechanical Properties

Grade Tensile Strength (MPa) min Yield Strength 0.2% Proof (MPa) min Elongation (% in 50mm) min Hardness
Rockwell B (HR B) max Brinell (HB) max
316 515 205 40 95 217
316L 485 170 40 95 217

Equivalent Grades for 316L Stainless Steel Wire mesh

STANDARD WERKSTOFF NR. UNS JIS BS GOST AFNOR EN
SS 316 1.4401 / 1.4436 S31600 SUS 316 316S31 / 316S33 Z7CND17‐11‐02 X5CrNiMo17-12-2 / X3CrNiMo17-13-3
SS 316L 1.4404 / 1.4435 S31603 SUS 316L 316S11 / 316S13 03Ch17N14M3 / 03Ch17N14M2 Z3CND17‐11‐02 / Z3CND18‐14‐03 X2CrNiMo17-12-2 / X2CrNiMo18-14-3

SS 316/316L Wire Mesh Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

316/316L Steel Wire mesh Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2024-01-04T17:14:57+05:30December 4th, 2021|

Stainless Steel 310H Wire Mesh Manufacturers In India

Stainless Steel 310H Wire Mesh Manufacturers In India

Sachiya Steel International is one of the Leading Manufacturer And Exporter Of High Quality Stainless Steel 310H Wire Mesh, which Good resistance to mildly corrosive atmospheres, but significantly less than Grade 310H due to the Sulphur addition; the sulphide inclusions act as pit initiation sites.  Grade 310 should not be exposed to marine or other similar environments, as these will result in rapid pitting corrosion. Because the sulphide inclusions in 310 are primarily aligned along the rolling direction the corrosion resistance is particularly reduced in cross-sections.

Stainless Steel 310H Wire Mesh

It is like other common austenitic stainless steels, is subject to stress corrosion cracking in chloride containing environments above about 50°C. Good oxidation resistance in intermittent service to 760°C and in continuous service to 870°C. Not generally recommended but, if unavoidable use Grade 308L or 309 electrodes. AS 1554.6 does not pre-qualify welding of 303.  Welds must be annealed for maximum corrosion resistance, but even then poor mechanical and corrosion properties will result. For ultra-high machining rates there are also available special grade variants such as Ugima 303UX. This includes copper to reduce the work hardening rate, in addition to the usual high Sulphur and Improved Machinability steel making practices.

Nuts and bolts. Bushings. Shafts. Electrical switchgear components. Gears. In general any component that is heavily machined and where the corrosion resistance and fabrication properties of 310H are viable. Grade 310H (UNS S31009) has a carbon content restricted to exclude the lower end of the 310 range, so is the grade of choice for high temperature applications.

SS 310H Wire mesh Specifications

Specifications : ASTM A 164 ASME SA 164
Standard : DIN, ASTM, BS and all International Standards
Length : 30m to 100″
Width : 1m to 48″
Type : Wire Mesh , Hexagonal Wire mesh, Welding Wire mesh, Netting Wire mesh, Woven Wire mesh , Spring Steel wire mesh, Fencing Wire mesh etc.

310H Stainless Steel Wire Mesh Chemical Composition

Grade C Mn Si P S Cr Mo Ni N
SS 310H 0.04 – 0.10 2 max 1.00 max 0.045 max 0.030 max 24.00 – 26.00 19.00 – 21.00 53.885 min

Stainless Steel 310H Wire mesh Mechanical Properties

Density Melting Point Tensile Strength Yield Strength (0.2%Offset) Elongation
7.9 g/cm3 1402 °C (2555 °F) Psi – 75000 , MPa – 515 Psi – 30000 , MPa – 205 40%

Equivalent Grades for 310H Stainless Steel Wire mesh

STANDARD WERKSTOFF NR. UNS JIS BS GOST AFNOR EN
SS 310H S31009

SS 310H Wire Mesh Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

310H Steel Wire mesh Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2024-02-23T13:20:03+05:30December 3rd, 2021|
Go to Top