Sachiya Steel International

Female Fittings connectors

Incoloy 925 Tube to Female Pipes Manufacture

[bt_section][bt_row][bt_column width=”1/1″][bt_text]

 

Sachiya Steel International offers a wide range of Incoloy Alloy 925 Tube to Female Pipes, where most any commercial coolant may be used in the machining operations. Incoloy 925 Tube Fittings is ideally suited to down – hole and surface gas well components such as valves, hangers, nipples, tool joints, fasteners and packers. Soft die materials such as zinc alloys and bronze in Incoloy 925 Compression Fittings are used to produce good finishing and avoid galling problems.

The precipitation – hardening (age – hardening) heat treatment in Incoloy 925 Female Connector Fittings causes precipitation of gamma prime phase, Ni3 (Al, Ti), where the phase greatly increases both the hardness and strength of the alloy. The metallurgical composition of Incoloy 925 Ferrule Fittings makes them outstandingly resistant to crevice corrosion and pitting. The resistance of Incoloy 925 Double Ferrule Fittings is developed by the precipitation of the gamma phase through solubilization and aging heat treatment, so as to maintain ductility and toughness at high levels.

Incoloy Alloy 925 Tube to Female Pipes | Incoloy Alloy 925 Tube to Female Pipes | Incoloy Alloy 925 Tube to Female Pipes | Incoloy Alloy 925 Tube to Female Pipes | Incoloy Alloy 925 Tube to Female Pipes | Incoloy Alloy 925 Tube to Female Pipes | Incoloy Alloy 925 Tube to Female Pipes | Incoloy Alloy 925 Tube to Female Pipes

Incoloy 925 Compression Tube Fittings combines the high strength of a precipitation – harden able alloy with the excellent corrosion resistance of alloy 825. These Alloy 925 Tube Fittings is an age harden able nickel – iron – chromium alloy designed to provide a combination of high strength and good corrosion resistance. Alloy 925 Compression Fittings is designed primarily for applications in the production of gas. Alloy 925 Female Connector Fittings is particularly resistant to sulfide – induced stress cracking and stress – corrosion cracking.

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Incoloy 925 Tube to Female Pipes Specifications
Specifications : ASTM B366 ASME SB 366
Size : OD -: 6mm to 38mm, Inch -: 1/4″ to 1 1/2″
Thread : NPT, BSP, BSPT, UNF, ISO, SAE etc.
Pressure Rating
 : 3000 – 9250 PSI
Applicable Temperature
 : 150-400 C
Type
 : Single Ferrule tube fitting, Double Ferrule tube fitting, Hydraulic tube fitting, Instrumentation tube fitting.
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]

925 Incoloy Alloy Tube to Female Pipes Fitting Chemical Composition

Grade C Mn Si Fe S Cr Cu Ni
925 min. – – – 22.0 – 19.5 1.5 42.0
max. – – – – – 22.5 3.0 46.0
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]

Incoloy Alloy 925 Tube to Female Pipes Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Incoloy 925 Tube to Female Pipes Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

 

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Incoloy Alloy 925 Tube to Female Pipes
inconel pipe fitting 300x300 2

Sachiya Steel International offers a wide range of Incoloy Alloy 925 Tube to Female Pipes, where most any commercial coolant may be used in the machining operations.

Product Brand: Sachiya Steel International

Product In-Stock: InStock

Editor's Rating:
5
[/bt_text][/bt_column][/bt_row][bt_row][/bt_row][/bt_section]
By |2021-07-08T13:09:06+05:30July 8th, 2021|

Incoloy 330 Tube to Female Pipes Manufacture

[bt_section][bt_row][bt_column width=”1/1″][bt_text]

 

Sachiya Steel International offers an extensive array of Incoloy 330 Tube to Female Pipes to the clients, which has a low coefficient of expansion, excellent ductility, and high strength. In fact, the work hardening rate of Inconel 330 Tube Fittings is similar to that of stainless steel 305. Inconel 330 Compression Fittings performs well under cyclic conditions of heating and cooling and in alternate carburizing and oxidizing atmospheres. Due to its relatively high strength and work hardening rate, Inconel 330 Female Connector Fittings is more difficult to cold form than standard 18 – 8 stainless steels.

In general, nickel alloys except alloy 600 outperform Ra 330 Female Connector Fittings in creep strength, which are further often encountered in extreme environments. SS 330 Female Connector Fittings is often used in Off – Shore Oil Drilling Companies, Petrochemicals, Power Generation and more. Carburization and oxidation resistance of Ra 330 Tube Fittings to 2100 Degree F (1148 Degree C) are enhanced by a nominal 1.25 % silicon addition.

Incoloy 330 Tube to Female Pipes | Incoloy 330 Tube to Female Pipes | Incoloy 330 Tube to Female Pipes | Incoloy 330 Tube to Female Pipes | Incoloy 330 Tube to Female Pipes | Incoloy 330 Tube to Female Pipes | Incoloy 330 Tube to Female Pipes | Incoloy 330 Tube to Female Pipes | Incoloy 330 Tube to Female Pipes | Incoloy 330 Tube to Female Pipes

SS 330 Tube Fittings are also used in the following applications: Furnaces, muffles, retorts and conveyor systems; Industrial heating; Heat treating baskets and fixtures. Ra 330 Compression Fittings have resistant to thermal shock, good strength at elevated temperature, and also chloride ion stress corrosion cracking resistance. SS 330 Compression Fittings is also used for everything from resistors, mechanical components, springs and heating applications.

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Incoloy 330/ SS 330/ Ra 330 Tube to Female Pipes Specifications
Specifications : ASTM B366 ASME SB 366
Size : OD -: 6mm to 38mm, Inch -: 1/4″ to 1 1/2″
Thread : NPT, BSP, BSPT, UNF, ISO, SAE etc.
Pressure Rating : 3000 – 330/ SS 330/Ra 3300 PSI
Applicable Temperature
 : 150-400 C
Type
 : Single Ferrule tube fitting, Double Ferrule tube fitting, Hydraulic tube fitting, Instrumentation tube fitting.
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]

330 Incoloy Alloy Tube to Female Pipes Fitting Chemical Composition

Grade C Mn Si P S Cr Cu N
330 min. – – 0.75 – – 17.0 – 34.0
max. 0.08 2.0 1.50 0.030 – 20.0 – 37.0

Equivalent Grades for ss 330 Incoloy Tube to Female Pipes Fitting

Grade UNS No Old British Euronorm GOST Japanese JIS
BS En No AFNOR
Incoloy 330 N08330 – – 1.4886 – – –
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]

Incoloy Alloy 330/ SS 330/ Ra 330 Tube to Female Pipes Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Incoloy 330/ SS 330/ Ra 330 Tube to Female Pipes Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

 

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Incoloy 330 Tube to Female Pipes
inconel pipe fitting 300x300 1

Sachiya Steel International offers an extensive array of Incoloy 330 Tube to Female Pipes to the clients, which has a low coefficient of expansion, excellent ductility, and high strength.

Product Brand: Sachiya Steel International

Product In-Stock: InStock

Editor's Rating:
5
[/bt_text][/bt_column][/bt_row][bt_row][/bt_row][/bt_section]
By |2021-07-08T12:53:09+05:30July 8th, 2021|

Incoloy 825 Tube to Female Pipes Manufacture

[bt_section][bt_row][bt_column width=”1/1″][bt_text]

Sachiya Steel International offers a wide range of Incoloy Alloy 825 Tube to Female Pipes, where most of any commercial coolant may be used in the machining operations. Incoloy 825 Tube Fittings has many different industrial applications, some of which include: Phosphoric acid evaporators, Propeller shafts, Tank trucks, and more. Incoloy 825 Compression Fittings is an all – purpose project alloy, have good corrosion resistance of the acid and alkali metal property in both oxidation and reduction environments.

Incoloy 825 Compression Tube Fittings has excellent resistance to sulfuric and phosphoric acids and resists inter – granular corrosion in the as – welded condition. The commonly used welding methods work well with Incoloy 825 Female Connector Fittings, where matching alloy filler metal should be used. Incoloy 825 Ferrule Fittings should not be used at temperatures where creep – rupture properties are design factors. Incoloy 825 Double Ferrule Fittings is particularly useful in sulfuric & phosphoric acids, sulfur containing flue gases, sour gas, oil wells and sea water.

Incoloy Alloy 825 Tube to Female Pipes | Incoloy Alloy 825 Tube to Female Pipes | Incoloy Alloy 825 Tube to Female Pipes | Incoloy Alloy 825 Tube to Female Pipes | Incoloy Alloy 825 Tube to Female Pipes | Incoloy Alloy 825 Tube to Female Pipes | Incoloy Alloy 825 Tube to Female Pipes | Incoloy Alloy 825 Tube to Female Pipes |Incoloy Alloy 825 Tube to Female Pipes | Incoloy Alloy 825 Tube to Female Pipes | Incoloy Alloy 825 Tube to Female Pipes

Alloy 825 Tube Fittings is developed to provide exceptional resistance to numerous corrosive environments, both oxidizing and reducing. Applications of Alloy 825 Compression Fittings include chemical processing, pollution control, oil and gas recovery, acid production, pickling operations, nuclear fuel reprocessing, and handling of radioactive wastes. Alloy 825 Female Connector Fittings is a nickel – iron – chromium alloy with additions of copper, molybdenum and titanium, which has a face – centered – cubic crystal structure.

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Incoloy 825 Tube to Female Pipes Specifications
Specifications : ASTM B366 ASME SB 366
Size : OD -: 6mm to 38mm, Inch -: 1/4″ to 1 1/2″
Thread : NPT, BSP, BSPT, UNF, ISO, SAE etc.
Pressure Rating
 : 3000 – 8250 PSI
Applicable Temperature
 : 150-400 C
Type
 : Single Ferrule tube fitting, Double Ferrule tube fitting, Hydraulic tube fitting, Instrumentation tube fitting.
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]

825 Incoloy Alloy Tube to Female Pipes Fitting Chemical Composition

Grade C Mn Si Fe S Cr Cu Ti
825 min. – – – 22.0 – 19.5 1.5 0.6
max. 0.05 1.0 0.5 – 0.015 23.5 3.0 1.2

Incoloy Alloy 825 Tube to Female Pipes Fitting Mechanical Properties

Grade Tensile Strength (MPa) min Yield Strength 0.2% Proof (MPa) min Elongation (% in 50mm) min Hardness
Rockwell B (HR B) max Brinell (HB) max
825 Psi – 80,000 , MPa – 550 Psi – 32,000 , MPa –220 30 – –

Equivalent Grades for 825 Incoloy Tube to Female Pipes Fitting

Grade UNS No Old British Euronorm GOST Japanese JIS
BS En No AFNOR
Incoloy 825 N08825 NA 16 NiCr21Mo 2.4858 NFE30C20DUM ЭП703 NCF 825
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]

Incoloy Alloy 825 Tube to Female Pipes Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Incoloy 825 Tube to Female Pipes Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

 

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Incoloy Alloy 825 Tube to Female Pipes
female manometer 3 2

Sachiya Steel International offers a wide range of Incoloy Alloy 825 Tube to Female Pipes, where most of any commercial coolant may be used in the machining operations.

Product Brand: Sachiya Steel International

Product In-Stock: InStock

Editor's Rating:
5
[/bt_text][/bt_column][/bt_row][bt_row][/bt_row][/bt_section]
By |2021-07-06T11:58:06+05:30July 6th, 2021|

Incoloy 800 Tube to Female Pipes Manufacture

[bt_section][bt_row][bt_column width=”1/1″][bt_text]

 

Sachiya Steel International offers a wide quality range of Incoloy 800 Tube to Female Pipes, which has excellent creep strength at temperatures above 1290 Degree F (700 Degree C). Incoloy 800 Tube Fittings is often used in Ethylene furnace quench boilers, Hydrocarbon cracking, Valves, fittings and other components exposed to corrosive attack from 1100 Degree F – 1800 Degree F.

Incoloy 800H Tube Fittings is also used in Heat exchangers and process piping, along with Carburizing fixtures and retorts. For applications in Incoloy 800HT Tube Fittings requiring greater resistance to stress rupture and creep, especially at temperatures above 1500 Degree F (816 Degree C), 800HT are used. Machining characteristics of Incoloy 800 Compression Fittings are similar to that of iron – based alloys.

Incoloy 800 Tube to Female Pipes | Incoloy 800 Tube to Female Pipes | Incoloy 800 Tube to Female Pipes | Incoloy 800 Tube to Female Pipes | Incoloy 800 Tube to Female Pipes | Incoloy 800 Tube to Female Pipes | Incoloy 800 Tube to Female Pipes | Incoloy 800 Tube to Female Pipes | Incoloy 800 Tube to Female Pipes | Incoloy 800 Tube to Female Pipes

For high temperature applications requiring optimum rupture and creep properties, Incoloy 800H Compression Fittings are used. Incoloy 800HT Compression Fittings has always been known to contain properties for high temp strength and resistance to carburization, oxidation and other high temp corrosion.

These additions allow Incoloy 800 Female Connector Fittings to adapt to the needs of a variety of industries and enable leading metal companies to offer a range of Incoloy shapes and designs. Alloy 800 Tube Fittings is used in the heat processing equipment, industrial incinerators, chemical processing industries etc. In hot or concentrated solutions, rates of Alloy 800 Compression Fittings are usually too high for reasonable service life.

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Incoloy 800/800H/800HT Tube to Female Pipes Specifications
Specifications : ASTM B366 ASME SB 366
Size : OD -: 6mm to 38mm, Inch -: 1/4″ to 1 1/2″
Thread : NPT, BSP, BSPT, UNF, ISO, SAE etc.
Pressure Rating
 : 3000 – 800/800H/800HT0 PSI
Applicable Temperature
 : 150-400 C
Type
 : Single Ferrule tube fitting, Double Ferrule tube fitting, Hydraulic tube fitting, Instrumentation tube fitting.
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]

800/ 800H/ 800HT Incoloy Alloy Tube to Female Pipes Fitting Chemical Composition

Grade C Mn Si Fe S Cr Al-Ti Ni
800 min. – – – 39.5 – 19.0 0.15 30.0
max. 0.1 1.5 1.0 – 0.015 23.0 0.60 35.0
800H min. 0.05 – – 39.5 – 19.0 0.15 30.0
max. 0.1 1.5 1.0 – 0.015 23.0 0.60 35.0
800HT min. 0.06 – – 39.5 – 19.0 0.85/0.25 30.0
max. 0.1 1.5 1.0 – 0.015 23.0 1.20/0.60 35.0

Incoloy Alloy 800/ 800H/ 800HT Tube to Female Pipes Fitting Mechanical Properties

Grade Tensile Strength (MPa) min Yield Strength 0.2% Proof (MPa) min Elongation (% in 50mm) min Hardness
Rockwell B (HR B) max Brinell (HB) max
800-H-HT Psi – 75,000 , MPa – 520 Psi – 30,000 , MPa –205 30 – –

Equivalent Grades for 800 / 800H / 800HT Incoloy Tube to Female Pipes Fitting

STANDARD WERKSTOFF NR. UNS JIS BS GOST AFNOR EN OR
Incoloy 800 1.4876 N08800 NCF 800 NA 15 ЭИ670 Z8NC32-21 X10NiCrAlTi32-20 XH32T
Incoloy 800H 1.4958 / 1.4876 N08810 NCF 800H NA 15(H) ЭИ670 Z8NC33-21 X5NiCrAlTi31-20 XH32T
Incoloy 800HT 1.4859 / 1.4876 N08811 NCF 800HT NA 15(HT) ЭИ670 – X8NiCrAlTi32-21 XH32T
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]

Incoloy Alloy 800/800H/800HT Tube to Female Pipes Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Incoloy 800/800H/800HT Tube to Female Pipes Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

 

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Incoloy 800 Tube to Female Pipes
female manometer 3 1

Sachiya Steel International offers a wide quality range of Incoloy 800 Tube to Female Pipes, which has excellent creep strength at temperatures above 1290 Degree F (700 Degree C).

Product Brand: Sachiya Steel International

Product In-Stock: InStock

Editor's Rating:
5
[/bt_text][/bt_column][/bt_row][bt_row][/bt_row][/bt_section]
By |2021-07-06T11:42:13+05:30July 6th, 2021|

Inconel Alloy 718 Tube to Female Pipes Manufactures In India

Inconel Alloy 718 Tube to Female Pipes Manufactures In India

Sachiya Steel International deals in an all-embracing range of Inconel Alloy 718 Tube to Female Pipes, which is age – harden able with a unique property of slow aging response that permits heating and cooling during annealing without the danger of cracking. Inconel 718 Tube Fittings can be readily machined but due to its high strength and work hardening characteristics, tooling, operating speeds and coolants should be considered.

After fabrication, Inconel 718 Compression Fittings can be heat treated as required and as per the applicable specification. Inconel 718 Female Connector Fittings is usually provided in the solution annealed condition, but can be also being supplied in the aged hardened or precipitation heat treated condition prior to forming. Inconel 718 Ferrule Fittings has been used world – wide in aerospace, aircraft, oil, and chemical industries, and also nuclear power plants because of its high strength, excellent ductility, good formability and weldability, etc.

These Inconel 718 Double Ferrule Fittings is actually an age – harden able Nickel – Chromium – Columbium (Niobium) – Molybdenum alloy with high strength, corrosion – resistance, and good fabrication characteristics. Inconel 718 Compression Tube Fittings is a high strength nickel – chromium material and a nickel super alloy frequently used for cryogenic storage tanks, turbines, down hole shafting and well head parts. We have met every challenge of providing quality, timely, cost – effective solutions for these Alloy 718 Tube Fittings and specialty fastener applications.

Inconel Alloy 718 Tube to Female Pipes Specifications
Specifications : ASTM B366 ASME SB 366
Size : OD -: 6mm to 38mm, Inch -: 1/4″ to 1 1/2″
Thread : NPT, BSP, BSPT, UNF, ISO, SAE etc.
Pressure Rating
 : 3000 – 7180 PSI
Applicable Temperature
 : 150-400 C
Type
 : Single Ferrule tube fitting, Double Ferrule tube fitting, Hydraulic tube fitting, Instrumentation tube fitting.

718 Inconel Alloy Tube to Female Pipes Fitting Chemical Composition

Grade C Mn Si Fe S Cr Al Ni
718 min. – – – bal – 17.0 0.2 50.0
max. 0.08 0.35 0.35 bal 0.01 21.0 0.8 55.0

Inconel Alloy 718 Tube to Female Pipes Fitting Mechanical Properties

Element Density Melting Point Tensile Strength Yield Strength (0.2%Offset) Elongation
825 8.14 g/cm3
1400 °C (2550 °F)
Psi – 80,000 , MPa – 550 Psi – 32,000 , MPa – 220 30 %

Equivalent Grades for 718 Inconel Tube to Female Pipes Fitting

Grade UNS No Old British Euronorm GOST Japanese JIS
BS En No AFNOR
Inconel 718 N07718 – – 2.4668 – – –

Inconel Alloy 718 Tube to Female Pipes Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Inconel 718 Tube to Female Pipes Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2024-04-26T12:41:31+05:30July 5th, 2021|

Inconel Alloy 625 Tube to Female Pipe Manufacturers In India

Inconel Alloy 625 Tube to Female Pipe Manufacturers In India

Sachiya Steel International offers a wide range of Inconel Alloy 625 Tube to Female Pipes, which has good strength / ductility properties from sub – zero temperatures to over 980 Degree C. Inconel 625 Tube Fittings in the soft annealed condition are characterized by good resistance to mineral acids such as nitric, phosphoric, hydrochloric and sulfuric acid. Inconel 625 Compression Fittings has excellent forming and welding characteristics, where hot forming should be performed within a temperature range of 1700 Degree F to 2150 Degree F.

Some applications requiring the combination of strength and corrosion resistance offered by Inconel 625 Female Connector Fittings are bubble caps, reaction vessels, tubing, distillation columns, transfer piping, valves and heat exchangers. Inconel 625 Ferrule Fittings is produced by vacuum induction melting or by AOD refining, where niobium stabilizes the alloy contrary to sensitization in the course of welding. Inconel 625 Double Ferrule Fittings is often used for Air Pollution Control, such as in chimney liners, flue gas desulfurization (FGD) components, dampers, etc. Inconel 625 Compression Tube Fittings is also used in oil and gas production where hydrogen sulfide and elementary sulfur exist at temperature in excess of 150 Degree C.

Inconel Alloy 625 Tube to Female Pipes

Inconel 625 Tube Fittings is a nickel – chromium alloy used for its high strength, outstanding corrosion resistance and excellent fabricability. Alloy 625 Compression Fittings is not only nickel based super alloy, but also Non – Magnetic and Corrosion resistant in nature.

Inconel Alloy 625 Tube to Female Pipes Specifications
Specifications : ASTM B366 ASME SB 366
Size : OD -: 6mm to 38mm, Inch -: 1/4″ to 1 1/2″
Thread : NPT, BSP, BSPT, UNF, ISO, SAE etc.
Pressure Rating
 : 3000 – 6250 PSI
Applicable Temperature
 : 150-400 C
Type
 : Single Ferrule tube fitting, Double Ferrule tube fitting, Hydraulic tube fitting, Instrumentation tube fitting.

625 Inconel Alloy Tube to Female Pipes Fitting Chemical Composition

Grade C Mn Si Fe S Cr2 Al-Ti Ni
625 min. – – – – – 20.0 – 58.0
max. 0.10 0.50 0.50 5.0 0.015 23.0 0.40 –

Inconel Alloy 625 Tube to Female Pipes Fitting Mechanical Properties

Grade Tensile Strength (MPa) min Yield Strength 0.2% Proof (MPa) min Elongation (% in 50mm) min Hardness
Rockwell B (HR B) max Brinell (HB) max
625 Psi – 1,35,000 , MPa -930 Psi – 75,000 , MPa – 517 42.5 – –

Equivalent Grades for 600 Inconel Tube to Female Pipes Fitting

Grade UNS No Old British Euronorm GOST Japanese JIS
BS En No AFNOR
Inconel 625 N06625 NA 21 NiCr22Mo9Nb 2.4856 NC22DNB4M ХН75МБТЮ NCF 625

Inconel Alloy 625 Tube to Female Pipes Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Inconel 625 Tube to Female Pipes Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2024-04-27T16:04:29+05:30July 5th, 2021|

Inconel 601 Tube to Female Pipes Manufacture

[bt_section][bt_row][bt_column width=”1/1″][bt_text]

 

Sachiya Steel International offers a wide range of Inconel Alloy 601 Tube to Female Pipes, where oxidation resistance is further enhanced by the aluminum content. Inconel 601 Tube Fittings is used in several industries such as Thermal Processing, Power Generation, Aerospace and Chemical Processing. Tubing in these Inconel 601 Compression Fittings has been used in ceramic tile production in the latest designs of roller hearth ovens as the material resists the high temperature firing cycle and the corrosive effects of the glazes and stucco applied to the tiles.

Inconel 601 Female Connector Fittings is often used in Radiant tubes, Steam super – heater tube supports, Muffles and retorts, Strand annealing tubes, etc. These Inconel 601 Ferrule Fittings has good strength, toughness and ductility, and can be used at cryogenic temperatures. All standard machining operations may be performed on Inconel 601 Double Ferrule Fittings, where best machinability is obtained in the solution – treated condition.

Inconel Alloy 601 Tube to Female Pipes | Inconel Alloy 601 Tube to Female Pipes | Inconel Alloy 601 Tube to Female Pipes | Inconel Alloy 601 Tube to Female Pipes | Inconel Alloy 601 Tube to Female Pipes | Inconel Alloy 601 Tube to Female Pipes | Inconel Alloy 601 Tube to Female Pipes | Inconel Alloy 601 Tube to Female Pipes | Inconel Alloy 601 Tube to Female Pipes

In pollution – control applications, these Inconel 601 Compression Tube Fittings is used for thermal reactors in exhaust systems of gasoline engines and for combustion chambers in solid – waste incinerators. Alloy 601 Tube Fittings is also used in tube supports grid barriers, and ash – handling systems for power generation equipment. These Inconel 601 Compression Fittings is welded using gas – tungsten arc welding, gas metal – arc welding, shielded metal – arc welding, and submerged – arc welding methods.

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Inconel 601 Tube to Female Pipes Specifications
Specifications : ASTM B366 ASME SB 366
Size : OD -: 6mm to 38mm, Inch -: 1/4″ to 1 1/2″
Thread : NPT, BSP, BSPT, UNF, ISO, SAE etc.
Pressure Rating
 : 3000 – 6010 PSI
Applicable Temperature
 : 150-400 C
Type
 : Single Ferrule tube fitting, Double Ferrule tube fitting, Hydraulic tube fitting, Instrumentation tube fitting.
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]

601 Inconel Alloy Tube to Female Pipes Chemical Composition

Grade C Mn Si Fe S Cr Cu Ni
601 min. – – – Bal – 21.0 – 58.0
max. 0.10 1.0 0.5 Bal 0.015 25.0 1.0 63.0

Inconel Alloy 601 Tube to Female Pipes Mechanical Properties

Grade Tensile Strength (MPa) min Yield Strength 0.2% Proof (MPa) min Elongation (% in 50mm) min Hardness
Rockwell B (HR B) max Brinell (HB) max
601 Psi – 95,000 , MPa -655 Psi – 45,000 , MPa – 310 40 – –

Equivalent Grades for 600 Inconel Tube to Female Pipes

Grade UNS No Old British Euronorm GOST Japanese JIS
BS En No AFNOR
Inconel 601 N06601 NA 49 NiCr23Fe 2.4851 NC23FeA XH60BT NCF 601
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]

Inconel Alloy 601 Tube to Female Pipes Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Inconel 601 Tube to Female Pipes Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

 

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Inconel Alloy 601 Tube to Female Pipes
female manometer 2 1

Sachiya Steel International offers a wide range of Inconel Alloy 601 Tube to Female Pipes, where oxidation resistance is further enhanced by the aluminum content.

Product Brand: Sachiya Steel International

Product In-Stock: InStock

Editor's Rating:
5
[/bt_text][/bt_column][/bt_row][/bt_section]
By |2021-07-03T11:56:04+05:30July 3rd, 2021|

Inconel 600 Tube to Female Pipes Manufacture

[bt_section][bt_row][bt_column width=”1/1″][bt_text]

 

Sachiya Steel International offers a wide range of Inconel Alloy 600 Tube to Female Pipes, which can be formed both ways i.e. cold – formed and hot – formed by different processes. Inconel 600 Tube Fittings is a superior choice for chemical processing equipment, heat treating muffles and retorts. Inconel 600 Compression Fittings is used in chemical processing, food processing, phenol condensers, heat treating, soap manufacture, vegetable vessel, fatty acid vessels, and so on.

Above this temperature in Inconel 600 Female Connector Fittings, grain growth may be objectionable, although very brief heating at 1900 Degree F will cause complete softening without undue grain growth. Typical of other nickel alloys, heavy – duty equipment in Inconel 600 Ferrule Fittings should be used along with sharp tooling and more than adequate cooling. Inconel 600 Double Ferrule Fittings is also used in evaporator tubes, flaking trays and tube sheets for the manufacture of sodium sulfide.

Inconel Alloy 600 Tube to Female Pipes | Inconel Alloy 600 Tube to Female Pipes | Inconel Alloy 600 Tube to Female Pipes | Inconel Alloy 600 Tube to Female Pipes | Inconel Alloy 600 Tube to Female Pipes | Inconel Alloy 600 Tube to Female Pipes | Inconel Alloy 600 Tube to Female Pipes

Typical applications of Inconel 600 Compression Tube Fittings include the chemical, aerospace, pulp and paper, heat treating and nuclear engineering industries. Alloy 600 Tube Fittings is as well used in springs, lock wire, seals, reactor vessels, fixtures machinery, process equipment, furnace seals fans. Alloy 600 Compression Fittings is a Nickel – Chromium – Iron alloy with good corrosion resistance, high strength at high temperatures and good oxidation resistance. Alloy 600 Female Connector Fittings basically offers good oxidation and corrosion resistance at a very high temperature range.

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Inconel 600 Tube to Female Pipes Specifications
Specifications : ASTM B366 ASME SB 366
Size : OD -: 6mm to 38mm, Inch -: 1/4″ to 1 1/2″
Thread : NPT, BSP, BSPT, UNF, ISO, SAE etc.
Pressure Rating
 : 3000 – 6000 PSI
Applicable Temperature
 : 150-400 C
Type
 : Single Ferrule tube fitting, Double Ferrule tube fitting, Hydraulic tube fitting, Instrumentation tube fitting.
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]

600 Inconel Alloy Tube to Female Pipes Fitting Chemical Composition

Grade C Mn Si Fe S Cr Cu Ni
600 min. – – – 6.0 – 14.0 – 72.0
max. 0.15 1.0 0.5 10.0 0.015 17.0 0.5 –

Inconel Alloy 600 Tube to Female Pipes Fitting Mechanical Properties

Grade Tensile Strength (MPa) min Yield Strength 0.2% Proof (MPa) min Elongation (% in 50mm) min Hardness
Rockwell B (HR B) max Brinell (HB) max
600 Psi – 95,000 , MPa -655 Psi – 45,000 , MPa – 310 40 – –

Equivalent Grades for 600 Inconel Tube to Female Pipes Fitting

Grade UNS No Old British Euronorm GOST Japanese JIS
BS En No AFNOR
Inconel 600 N06600 NA 13 NiCr15Fe 2.4816 NC15FE11M МНЖМц 28-2,5-1,5 NCF 600
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]

Inconel Alloy 600 Tube to Female Pipes Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Inconel 600 Tube to Female Pipes Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

 

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Inconel Alloy 600 Tube to Female Pipes
female manometer 1

Sachiya Steel International offers a wide range of Inconel Alloy 600 Tube to Female Pipes, which can be formed both ways i.e. cold – formed and hot – formed by different processes.

Product Brand: Sachiya Steel International

Product In-Stock: InStock

Editor's Rating:
5
[/bt_text][/bt_column][/bt_row][bt_row][/bt_row][/bt_section]
By |2021-07-03T11:40:52+05:30July 3rd, 2021|

Incoloy Alloy 20 Tube to Female Pipes Manufacture

[bt_section][bt_row][bt_column width=”1/1″][bt_text]

 

Sachiya Steel International is one of the prominent Manufacture & exporter in Incoloy Alloy 20 Tube to Female Pipes, which is commercially pure (99.6 %) wrought nickel. Alloy 20 Tube Fittings is normally limited to service at temperatures below 600 Degree F. At higher temperatures, Alloy 20 Compression Fittings can suffer from graphitization which can result in severely compromised properties. All hot working and cold working practices can be utilized when shaping Alloy 20 Female Connector Fittings. Hot working temperatures for Alloy 20 Ferrule Fittings should be between 1200 Degree F and 2250 Degree F with heavy forming to be performed at temperatures above 1600 Degree F.

Annealing of Alloy 20 Double Ferrule Fittings should be performed at a temperature between 1300 Degree F and 1600 Degree F. Care should be taken when choosing the anneal temperature and time at temperature for Carpenter 20 Compression Tube Fittings can greatly influence the mechanical properties and structure of the material. When operating temperatures are expected to exceed 600 Degree F, carbon content in Carpenter 20 Female Connector Fittings becomes critical.

Incoloy Alloy 20 Tube to Female Pipes | Incoloy Alloy 20 Tube to Female Pipes | Incoloy Alloy 20 Tube to Female Pipes | Incoloy Alloy 20 Tube to Female Pipes | Incoloy Alloy 20 Tube to Female Pipes | Incoloy Alloy 20 Tube to Female Pipes | Incoloy Alloy 20 Tube to Female Pipes | Incoloy Alloy 20 Tube to Female Pipes

The lower carbon content of Carpenter 20 Tube Fittings makes the material resistant to graphitization and therefore less subject to embrittlement. Carpenter 20 Compression Fittings is approved for construction of pressure vessels and components under ASME Boiler and Pressure Vessel Code Section VIII, Division 1. Carpenter 20 Ferrule Fittings has good mechanical properties and excellent resistance to many corrosive environments.

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Alloy 20 Tube to Female Pipes Specifications
Specifications : ASTM B366 ASME SB 366
Size : OD -: 6mm to 38mm, Inch -: 1/4″ to 1 1/2″
Thread : NPT, BSP, BSPT, UNF, ISO, SAE etc.
Pressure Rating
 : 3000 – 4000 PSI
Applicable Temperature
 : 150-400 C
Type
 : Single Ferrule tube fitting, Double Ferrule tube fitting, Hydraulic tube fitting, Instrumentation tube fitting.
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]

Alloy 20 Tube to Female Pipes Fitting Chemical Composition

Alloy 20 Ni C Mo Mn Si Fe Cu S P Cr
32 – 38 0.02 max 2 – 3 1 – 2 0.7 max Bal 3 – 4 0.005 max 0.02 max 19 – 21

Alloy 20 Tube to Female Pipes Fitting Mechanical Properties

Density Melting Point Yield Strength (0.2%Offset) Tensile Strength Elongation
8.1 g/cm3 1443 °C (2430 °F) Psi – 35000 , MPa – 241 Psi – 80000 , MPa – 551 30 %

Equivalent Grades for 20 Alloy Tube to Female Pipes Fitting

STANDARD UNS WERKSTOFF NR. AFNOR EN JIS BS GOST
Alloy 20 N08020 2.4660 Z2NCUD31-20AZ NiCr20CuMo – – –
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]

Alloy 20 Tube to Female Pipes Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Alloy 20 Tube to Female Pipes Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

 

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Incoloy Alloy 20 Tube to Female Fittings
tube fittings slider

Sachiya Steel International is one of the prominent Manufacture & exporter in Incoloy Alloy 20 Tube to Female Fittings, which is commercially pure (99.6 %) wrought nickel.

Product Brand: Sachiya Steel International

Product In-Stock: InStock

Editor's Rating:
5
[/bt_text][/bt_column][/bt_row][bt_row][/bt_row][/bt_section]
By |2021-07-02T12:03:18+05:30July 2nd, 2021|

SMO 254 Tube to Female Pipe Manufacturers In India

SMO 254 Tube to Female Pipe Manufacturers In India

Sachiya Steel International is pioneer Manufacture and Exporter of quality SMO 254 Tube to Female Pipes, which is commercially pure (99.6 %) wrought nickel. SMO 254 Tube Fittings is normally limited to service at temperatures below 600 Degree F. At higher temperatures, SMO 254 Compression Fittings can suffer from graphitization which can result in severely compromised properties. All hot working and cold working practices for SMO 254 Female Connector Fittings can be utilized when shaping this alloy.

Hot working temperatures should be between 1200 Degree F and 2250 Degree F in SMO 254 Ferrule Fittings, with heavy forming to be performed at temperatures above 1600 Degree F. Annealing of SMO 254 Double Ferrule Fittings should be performed at a temperature between 1300 Degree F and 1600 Degree F. Care should be taken when choosing the anneal temperature and time at temperature for this can greatly influence the mechanical properties and structure of Alloy 254 Female Connector Fittings.

When operating temperatures in Alloy 254 Compression Tube Fittings are expected to exceed 600 Degree F, carbon content becomes critical. The lower carbon content of Alloy 254 Tube Fittings makes the material resistant to graphitization and therefore less subject to embrittlement. Alloy 254 Compression Fittings is approved for construction of pressure vessels and components under ASME Boiler and Pressure Vessel Code Section VIII, Division 1. Alloy 254 Ferrule Fittings has good mechanical properties and excellent resistance to many corrosive environments.

SMO 254 Tube to Female Pipes

SMO 254 Tube to Female Pipes Specifications
Specifications : ASTM A403 ASME SB 366
Size : OD -: 6mm to 38mm, Inch -: 1/4″ to 1 1/2″
Thread : NPT, BSP, BSPT, UNF, ISO, SAE etc.
Pressure Rating
 : 3000 – 4000 PSI
Applicable Temperature
 : 150-400 C
Type
 : Single Ferrule tube fitting, Double Ferrule tube fitting, Hydraulic tube fitting, Instrumentation tube fitting.

SMO 254 Tube to Female Pipes Fitting Chemical Composition

SMO 254 Ni C Mo Mn Si Fe Cu S P Cr
17.5 – 18.5
 0.02 max 6 – 6.5
 1 max 0.8 max – 0.5 – 1 0.01 max 0.03 max 19.5 – 20.5

SMO 254 Tube to Female Pipes Fitting Mechanical Properties

Density Melting Point Yield Strength (0.2%Offset) Tensile Strength Elongation
8.0 g/cm3 1320-1390 ℃ 300 650 35 %

Equivalent Grades for 254 SMO Tube to Female Pipes Fitting

STANDARD UNS WERKSTOFF NR. AFNOR EN JIS SIS GOST
SMO 254 S31254 1.4547 Z1 CNDU 20.18.06Az X1CrNiMoCuN20-18-7 – 2378 –

SMO 254 Tube to Female Pipes Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

SMO 254 Tube to Female Pipes Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 102544/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 102544 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 102544/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 102544 3.1 and EN 102544 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2024-04-10T18:34:24+05:30July 2nd, 2021|

SACHIYA STEEL INTERNATIONAL

D-2, Office No 3, Bharat Nagar CHS, Near Shalimar Cinema,
Grant Road ( East ) , Mumbai- 40007, Maharashtra, India.

[email protected]
[email protected]

OUR PRODUCTS

ACCREDITATION

certified stamp

© Copyright - 2024 | Sachiya Steel International | All Rights Reserved | Terms & Conditions | Privacy Policy | Sitemap

Go to Top