Washer

Titanium Gr 2 Washer Manufacturer

Sachiya Steel International is a known manufacturer and exporter of Titanium Gr 2 Washers, which is available in different sizes, unalloyed or alloyed. Because of all these qualities, these Titanium Grade 2 Flat Washers is the material of choice for any application where ease of formability is required and is commonly available as titanium plate and tubing.

Corrosion resistance of Titanium Grade 2 Lock Washers comes from a strongly adherent, stable, protective oxide film, which forms in the presence of oxygen. These Titanium Grade 2 Sealing Washers has intermediate and final annealing in inert gas or vacuum, where it can perform final heat treatments in vacuum.

Titanium Grade 2 Split Washers has highly stressed components such as connecting rods on expensive sports cars and some premium sports equipment and consumer electronics. Such contamination may raise the impurity level beyond that of these Titanium Grade 2 Slot Washers, thereby transforming the material into grade 3 or even grade 4.

Titanium Grade 2 Machine Washers is an attractive Grade of Titanium due to its excellent corrosion resistance, good formability, and limited strength. These Titanium Grade 2 Star Washers has fairish resistance in sulphuric acid and sodium hydroxide, where they do not resist in reducing acids, chlorides gases. Titanium Grade 2 Wire Spring Washers provides excellent welding properties and has excellent resistance to oxidation and corrosion. These Titanium Grade 2 Flat Spring Washers typically comes in the Annealed condition.

Titanium Gr2 Washer Specifications

Specifications : IS / BS / ASTM
Standard : ASTM B348
Length : upto 5 Meters
Size : M10 to M36
Type : Flat Washer, Lock Washer, Sealing Washer, Split Washer, Slot Washer, Machine Washer, Star Washer SPRINGS – Wire Spring & Flat Spring

Titanium Alloy Gr 2 Washers Chemical Composition

Grade Ti C Fe H N O Al V
Ti Grade2 99.2 min 0.1 max 0.3 max 0.015 max 0.03 max 0.25 max

Ti Grade2 Washer Mechanical Properties

Element Density Melting Point Tensile Strength Yield Strength (0.2%Offset) Elongation
Titanium Gr. 2 4.5 g/cm3 1665 °C (3030 °F) Psi – 49900 , MPa – 344 Psi – 39900 , MPa – 275 20 %

Equivalent Grades for Titanium Alloy Gr 2 Washer

STANDARD WERKSTOFF NR. UNS
Titanium Grade2 3.7035 R50400

Titanium Alloy Washers Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Ti Grade 2 Washers Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2023-12-07T18:26:57+05:30April 2nd, 2021|

Copper Nickel 90 Washers Manufacture

[bt_section][bt_row][bt_column width=”1/1″][bt_text]
Sachiya Steel International Exporter of ASTM B 151 Cu-Ni Machine Washer, Copper Nickel 90/10 Star Washer Exporter, Copper UNS C70600 Wire Spring, Cu-Ni WERKSTOFF NR. 2.0872 Flat Spring Manufacturer in India.

Copper Nickel 90 Washers has tensile, hardness, impact, creep and fatigue features, which have been abstracted from the relevant original literature. Cu-Ni 90 / 10 Lock Washers are most commonly specified within the marine, offshore, chemical, petrochemical and shipbuilding industries. Cupro Nickel 90 / 10 Sealing Washers are also widely used for handling seawater in all types of heat exchanger and cooling plant.

Nickel in Copper Nickel 90 / 10 Split Washers is soluble in copper and this renders the copper nickel alloys as single phase alpha structures. Cu-Ni 90 / 10 Slot Washers is a typical mix is 75 % copper, 25 % nickel, and a trace amount of manganese, where in the past, true silver coins were debased with such cupronickel. Cupro Nickel 90 / 10 Machine Washers are attacked by chromic, hydrochloric and nitric acids.

Copper Nickel 90 Washers | Copper Nickel 90 Washers | Copper Nickel 90 Washers | Copper Nickel 90 Washers

Copper Nickel 90 / 10 Star Washers is also resistant to the alkali chlorides, nitrates, sulfates and to ammonia and ammonium compounds. Cu-Ni 90 / 10 Wire Spring Washers is a Copper Nickel Iron alloy with a small content of manganese which allows excellent resistance to sea – and brackish water.

Meanwhile, Cupro Nickel 90 / 10 Flat Spring Washers are also being offered in different sizes and shapes to our customers. Copper Nickel 90 / 10 Washers is the low resistivity alloy used at temperature range up to 300 Degree C (570 Degree F).

 

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Cu-Ni Alloy 90/10 Washer Specifications
Specifications : ASTM
Standard : ASTM B151, B152
Length : M02 to M30
Size : M10 to M100
Type : Flat Washer, Lock Washer, Sealing Washer, Split Washer, Slot Washer, Machine Washer, Star Washer SPRINGS – Wire Spring & Flat Spring
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Copper Nickel Cu 90/10 Washers Chemical Composition
Cu-Ni 90/10 Cu Pb Mn Fe Zn Ni
88.6 min 0.05 max 1.0 max 1.8 max 1 max 9-11 max
Cu-Ni 90/10 Washer Mechanical Properties
Density Melting Point Yield Strength (0.2%Offset) Tensile Strength Elongation
8.1 g/cm3 1443 °C (2430 °F) Psi – 35,000, MPa – 241 Psi -80,000, MPa -551 30 %
Equivalent Grades for Copper Nickel 90/10 Washer
STANDARD UNS WERKSTOFF NR.
Cupro Nickel 90/10 C70600 2.0872
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Alloy Cu-Ni 90/10 Washers Application Industries
  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry
90/10 Cu-Ni Washers Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

 

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Copper Nickel 90 Washers
copper nickel 90 10 washers suppliers manufacturers india

Copper Nickel 90 Washers has tensile, hardness, impact, creep and fatigue features, which have been abstracted from the relevant original literature.

Product Brand: Sachiya Steel International

Product In-Stock: InStock

Editor's Rating:
5
[/bt_text][/bt_column][/bt_row][bt_row][/bt_row][/bt_section]
By |2021-04-02T11:21:37+05:30April 2nd, 2021|

Copper Nickel 30 Washers Manufacture

[bt_section][bt_row][bt_column width=”1/1″][bt_text]

 

Sachiya Steel International is a known producer of Copper Nickel 30 Washers, which is offered at leading market rates to our patrons. We can offer you Copper Nickel 30 Washers cut to your specifications through our precision plate saws, bar saws, shears and water jets. Another application of Copper Nickel 30 Washers is in the electrical engineering space where it can be used in the production of heating cables, anodes for television tubes and electric resistors.

The alpha dendrites in the cast structures of Copper Nickel 70 / 30 Sealing Washers contain a large amount of nickel starting from the center up to the edge of the dendrite. Another common use of Cu-Ni 70 / 30 Split Washers is in silver – coloured modern – circulated coins which are a typical mix of 75 % copper, 25 % nickel, and a trace amount of manganese.

Cupro Nickel 70 / 30 Slot Washers is often used in Factors; Development; Resistance; Reasoning; Microfouling; Tubing, Cladding and Offshore Structures; Removal; Effects on Corrosion; Effects on Plant Operations.

Copper Nickel 30 Washers | Copper Nickel 30 Washers | Copper Nickel 30 Washers | Copper Nickel 30 Washers | Copper Nickel 30 Washers | Copper Nickel 30 Washers

Our clients can purchase Copper Nickel 70 / 30 Machine Washers in a mass amount from us at reasonable rates, which can also further cut to your requirements along with custom forgings made to your requirements. Cu-Ni 70 / 30 Star Washers is the most commonly used wrought copper alloy for marine engineering and can be found in seawater systems for naval.

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Cu-Ni Alloy 70/30 Washer Specifications
Specifications : ASTM
Standard : ASTM B151, B152
Length : M02 to M30
Size : M10 to M100
Type : Flat Washer, Lock Washer, Sealing Washer, Split Washer, Slot Washer, Machine Washer, Star Washer SPRINGS – Wire Spring & Flat Spring
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Copper Nickel Cu 70/30 Washers Chemical Composition
Cu-Ni 70/30 Cu Pb Mn Fe Zn Ni
88.6 min 0.05 max 1.0 max 1.8 max 1 max 9-11 max
Cu-Ni 70/30 Washer Mechanical Properties
Density Melting Point Yield Strength (0.2%Offset) Tensile Strength Elongation
8.1 g/cm3 1443 °C (2430 °F) Psi – 35,000, MPa – 241 Psi -80,000, MPa -551 30 %
Equivalent Grades for Copper Nickel 70/30 Washer
STANDARD UNS WERKSTOFF NR.
Cupro Nickel 70/30 C71500 2.0882
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Alloy Cu-Ni 70/30 Washers Application Industries
  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry
70/30 Cu-Ni Washers Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Material Testing


We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

 

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]No schema found.[/bt_text][/bt_column][/bt_row][/bt_section]
By |2021-03-31T11:24:10+05:30March 31st, 2021|

Copper Nickel 70 Washers Manufacture

[bt_section][bt_row][bt_column width=”1/1″][bt_text]

 

Sachiya Steel International is a known producer of Copper Nickel 70 Washers, which is offered at leading market rates to our patrons. We can offer you Copper Nickel 70 Washers cut to your specifications through our precision plate saws, bar saws, shears and water jets. Another application of Copper Nickel 70 Washers is in the electrical engineering space where it can be used in the production of heating cables, anodes for television tubes and electric resistors.

The alpha dendrites in the cast structures of Copper Nickel 70 / 30 Sealing Washers contain a large amount of nickel starting from the center up to the edge of the dendrite. Another common use of Cu-Ni 70 / 30 Split Washers is in silver – coloured modern – circulated coins which are a typical mix of 75 % copper, 25 % nickel, and a trace amount of manganese.

Cupro Nickel 70 / 30 Slot Washers is often used in Factors; Development; Resistance; Reasoning; Microfouling; Tubing, Cladding and Offshore Structures; Removal; Effects on Corrosion; Effects on Plant Operations.

Copper Nickel 70 Washers | Copper Nickel 70 Washers | Copper Nickel 70 Washers | Copper Nickel 70 Washers | Copper Nickel 70 Washers | Copper Nickel 70 Washers

Our clients can purchase Copper Nickel 70 / 30 Machine Washers in a mass amount from us at reasonable rates, which can also further cut to your requirements along with custom forgings made to your requirements. Cu-Ni 70 / 30 Star Washers is the most commonly used wrought copper alloy for marine engineering and can be found in seawater systems for naval.

 

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Cu-Ni Alloy 70/30 Washer Specifications
Specifications : ASTM
Standard : ASTM B151, B152
Length : M02 to M30
Size : M10 to M100
Type : Flat Washer, Lock Washer, Sealing Washer, Split Washer, Slot Washer, Machine Washer, Star Washer SPRINGS – Wire Spring & Flat Spring
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Copper Nickel Cu 70/30 Washers Chemical Composition
Cu-Ni 70/30 Cu Pb Mn Fe Zn Ni
88.6 min 0.05 max 1.0 max 1.8 max 1 max 9-11 max
Cu-Ni 70/30 Washer Mechanical Properties
Density Melting Point Yield Strength (0.2%Offset) Tensile Strength Elongation
8.1 g/cm3 1443 °C (2430 °F) Psi – 35,000, MPa – 241 Psi -80,000, MPa -551 30 %
Equivalent Grades for Copper Nickel 70/30 Washer
STANDARD UNS WERKSTOFF NR.
Cupro Nickel 70/30 C71500 2.0882
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Alloy Cu-Ni 70/30 Washers Application Industries
  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry
70/30 Cu-Ni Washers Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Material Testing


We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

 

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Copper Nickel 70 Washers
copper nickel 70 30 washers suppliers manufacturers india

Sachiya Steel International is a known producer of Copper Nickel 70 Washers, which is offered at leading market rates to our patrons. We can offer you Copper Nickel 70 Washers cut to your specifications through our precision plate saws, bar saws, shears and water jets.

Product Brand: Sachiya Steel International

Product In-Stock: InStock

Editor's Rating:
5
[/bt_text][/bt_column][/bt_row][/bt_section]
By |2021-03-31T11:17:50+05:30March 31st, 2021|

Incoloy 330 Washers Manufacture

[bt_section][bt_row][bt_column width=”1/1″][bt_text]

 

Sachiya Steel International offers a widespread range of Incoloy 330 Washers, which are used in environments where thermal cycling is frequent. Incoloy 330 Flat Washers is highly ductile and able to withstand high temperatures of up to 1148 Degree C, as well as extreme carburizing conditions and repeated quenching.

SS 330 Lock Washers is used extensively in elevated temperatures where resistance to the combined effects of thermal cycling and carburization is required. As a result of all of these features, Ra 330 Sealing Washers is a great choice for a wide variety of operations, particularly when versatility and ability to function in a variety of environments and processes is important.

Incoloy 330 Washers | Incoloy 330 Washers | Incoloy 330 Washers |Incoloy 330 Washers | Incoloy 330 Washers

Incoloy 330 Split Washers is often used in heat exchangers, general heat treating equipment and neutral and cyanide salt pots. SS 330 Slot Washers has a high tensile strength which enables it to sustain any amount of load placed upon it. The strength and oxidation resistance of Ra 330 Machine Washers at elevated temperatures make it a useful material.

Along with high tensile, creep and rupture strength, Incoloy 330 Star Washers has outstanding fatigue and thermal – fatigue strength. Even the weld wire, SS 330 Wire Spring Washers has increased levels of manganese to avoid hot cracking. Ra 330 Flat Spring Washers exhibits good strength at high temperatures and good resistance to oxidation and reduction environments.

 

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Incoloy 330/ SS 330/ Ra 330 Washer Specifications
Specifications : ASTM B408
Standard : DIN, ASTM, BS and all International Standards
Length : M02 to M33
Size : 3 mm to 200 mm
Type : Flat Washer, Lock Washer, Sealing Washer, Split Washer, Slot Washer, Machine Washer, Star Washer SPRINGS – Wire Spring & Flat Spring
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Incoloy 330/ SS 330/ Ra 330 Washers Chemical Composition
Grade C Mn Si P S Cr Cu N Fe
330 0.08 max 2 max 0.75-1.50 0.030 17.0-20.0 34.0-37.0
Alloy 330/ SS 330/ Ra 330 Washer Mechanical Properties
Density Melting Point Tensile Strength Yield Strength (0.2%Offset) Elongation
Equivalent Grades for Incoloy Alloy 330/ SS 330/ Ra 330 Washer
STANDARD WERKSTOFF NR. UNS JIS BS GOST AFNOR EN
Incoloy 330 1.4886 N08330
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Alloy 330/ SS 330/ Ra 330 Washers Application Industries
  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry
330/ SS 330/ Ra 330 Incoloy Washers Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and MacroTest
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

 

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Incoloy 330 Washers
inconel washer 500x500 1

Sachiya Steel International offers a widespread range of Incoloy 330 Washers, which are used in environments where thermal cycling is frequent.

Product Brand: Sachiya Steel International

Product In-Stock: InStock

Editor's Rating:
5
[/bt_text][/bt_column][/bt_row][/bt_section]
By |2021-03-26T14:27:18+05:30March 26th, 2021|

Incoloy 925 Washers Manufacture

[bt_section][bt_row][bt_column width=”1/1″][bt_text]

 

Sachiya Steel International is a known supplier and trader of Incoloy 925 Washers , which offers excellent resistance to corrosion and shows high strength. The additions of titanium and aluminum enable Incoloy Alloy 925 Flat Washers to be age – hardened while molybdenum and copper contents enhance resistance to corrosive media.

The resistance of Incoloy 925 Lock Washer is developed by the precipitation of the gamma phase through solubilization and aging heat treatment, so as to maintain ductility and toughness at high levels. The nickel content in Incoloy Alloy 925 Sealing Washers provides protection against chloride – iron stress corrosion cracking and in combination with molybdenum and copper, gives outstanding resistance to reducing chemicals.

Incoloy 925 Washers | Incoloy 925 Washers | Incoloy 925 Washers | Incoloy 925 Washers | Incoloy 925 Washers | Incoloy 925 Washers

Incoloy 925 Split Washer are in specific resistant to sulfuric and phosphoric acids, and are thus hot worked at 872 Degree C to 983 Degree C (1600 Degree F to 1800 Degree F). This treatment in Incoloy 925 Slot Washers is followed by an aging treatment at 1365 Degree F (740 Degree C) for 8 hours, furnace cooling to 1150 Degree F (620 Degree C), holding for 6 hours and air cooling.

Because of the resistance to sulfide stress cracking and stress-corrosion cracking in sour crude oil and natural gas, Incoloy Alloy 925 Machine Washer is used for surface gas-well and down-hole components including valves, hangers, tubular, landing nipples, packers and tool joints. Incoloy 925 Star Washers is designed primarily for applications in the production of gas.

 

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Incoloy 925 Washer Specifications
Specifications : ASTM B805
Standard : DIN, ASTM, BS and all International Standards
Length : M02 to M33
Size : 3 mm to 200 mm
Type : Flat Washer, Lock Washer, Sealing Washer, Split Washer, Slot Washer, Machine Washer, Star Washer SPRINGS – Wire Spring & Flat Spring
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Incoloy 925 Washers Chemical Composition
Grade C Mn Si S Cu Fe Ni Cr Al Ti
925 0.03 max 1.00 max 0.05 max 0.03 max 1.50 – 3.00 22.00 min 42.00 – 46.00 19.55 – 22.50 0.01-0.05 max
Alloy 925 Washer Mechanical Properties
Element Density Melting Point Tensile Strength Yield Strength (0.2%Offset) Elongation
925 8.14 g/cm3 1343°C MPa – 650 MPa – 300 30 %
Equivalent Grades for Incoloy Alloy 925 Washer
STANDARD WERKSTOFF NR. UNS JIS
Incoloy 925 N09925 NCF 925
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Alloy 925 Washers Application Industries
  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry
925 Incoloy Washers Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

 

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Incoloy 925 Washers
flat washer 500x500 1

Sachiya Steel International is a known supplier and trader of Incoloy 925 Washers , which offers excellent resistance to corrosion and shows high strength.

Product Brand: Sachiya Steel International

Product In-Stock: InStock

Editor's Rating:
5
[/bt_text][/bt_column][/bt_row][/bt_section]
By |2021-03-26T13:07:21+05:30March 26th, 2021|

Incoloy 825 Washers Manufacture

[bt_section][bt_row][bt_column width=”1/1″][bt_text]

 

Sachiya Steel International is a known manufacturer of Incoloy 825 Washers, which resists a wide range of severely corrosive environments and is especially resistant to pitting and crevice corrosion. Incoloy 825 Flat Washer is often used in spray bars, turbine shroud rings, bellows and heat – exchanger tubing in environmental control systems. Incoloy 825 Lock Washer is non – magnetic and immune to chloride ion stress corrosion cracking, where they form in a needle – like morphology and are incoherent with the matrix.

The nickel and chromium content in Incoloy 825 Sealing Washers provide resistance to oxidizing environments. Incoloy Alloy 825 Split Washer is also used in Flue gas desulfurization scrubbers and Weld Overlay. Incoloy 825 Slot Washers is as well used in is used in chemical processing, marine engineering, aerospace, pollution – control equipment, nuclear reactor applications and so on.

Incoloy 825 Washers | Incoloy 825 Washers | Incoloy 825 Washers | Incoloy 825 Washers | Incoloy 825 Washers | Incoloy 825 Washers

The oxidation and scaling resistance of Alloy 825 Machine Washers is superior to a number of heat resistant austenitic stainless steels such as in Grade 304, Grade 309, Grade 310 and Grade 347 up to 1800 Degree F (982 Degree C) and under cyclic heating and cooling conditions.

Incoloy Alloy 825 Star Washer has high resistance to oxidation at elevated temperatures up to 1050 Degree C, which is also supplied in the hot worked and annealed condition. These Incoloy 825 Spring Washers is a nickel – chromium – molybdenum – niobium alloy with excellent resistance to a variety of corrosive media.

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Incoloy 825 Washer Specifications
Specifications : ASTM B425
Standard : DIN, ASTM, BS and all International Standards
Length : M02 to M33
Size : 3 mm to 200 mm
Type : Flat Washer, Lock Washer, Sealing Washer, Split Washer, Slot Washer, Machine Washer, Star Washer SPRINGS – Wire Spring & Flat Spring
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Incoloy 825 Washers Chemical Composition
Grade C Mn Si S Cu Fe Ni Cr Al Ti
825 0.05 max 1.00 max 0.5 max 0.03 max 1.50 – 3.00 22.00 min 38.00 – 46.00 19.50 – 23.50 0.02 max 0.06 – 1.20
Alloy 825 Washer Mechanical Properties
Element Density Melting Point Tensile Strength Yield Strength (0.2%Offset) Elongation
825 8.14 g/cm3 1400 °C (2550 °F) Psi – 80,000 , MPa – 550 Psi – 32,000 , MPa – 220 30 %
Equivalent Grades for Incoloy Alloy 825 Washer
STANDARD WERKSTOFF NR. UNS JIS BS GOST AFNOR EN OR
Incoloy 825 2.4858 N08825 NCF 825 NA 16 ЭП703 NFE30C20DUM NiCr21Mo XH38BT
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Alloy 825 Washers Application Industries
  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry
825 Incoloy Washers Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Material Testing


We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and MacroTest
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

 

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Incoloy 825 Washers
flat washer

Sachiya Steel International is a known manufacturer of Incoloy 825 Washers, which resists a wide range of severely corrosive environments and is especially resistant to pitting and crevice corrosion.

Product Brand: Sachiya Steel International

Product In-Stock: InStock

Editor's Rating:
5
[/bt_text][/bt_column][/bt_row][/bt_section]
By |2021-03-23T14:12:29+05:30March 23rd, 2021|

Incoloy 800 Washers Manufacture

[bt_section][bt_row][bt_column width=”1/1″][bt_text]

 

Sachiya Steel International offers an extensive quality collection of Incoloy 800 Washers, which is often used in industrial furnace components and equipment, along with petrochemical and chemical processing. Excellent cold forming characteristics typically associated with the nickel-chromium alloys are exhibited with Incoloy 800 Flat Washers.

Offering superior high – temperature strength, Incoloy 800H Lock Washers are widely used in applications requiring heat resistance, as they do not become brittle due to sigma phase precipitation during use. Incoloy 800HT Sealing Washers will not become embrittled even after long periods of usage in the 1200 Degree F – 1600 Degree F range where many stainless steels become brittle.

Incoloy 800 Washers | Incoloy 800 Washers  | Incoloy 800 Washers | Incoloy 800 Washers | Incoloy 800 Washers | Incoloy 800 Washers

Alloy 800 Split Washers had been known for some time that this higher carbon alloy had higher creep and rupture properties than low – carbon material. For high temperature applications requiring optimum rupture and creep properties, Alloy 800H Machine Washers are used. Alloy 800HT Star Washers has good creep – rupture properties at temperatures above 1100 Degree F (600 Degree C). Another important feature of Incoloy 800 Wire Spring Washers is excellent resistance to chloride stress – corrosion cracking.

These Incoloy 800H Flat Spring Washers are known for their excellent strength at elevated temperatures and good corrosion resistance in a variety of corrosive environments. Incoloy 800HT Spring Washers is also used in Equipment for Heat – Treating, Hydrocarbon cracking, Pressure vessels and heat exchangers.

 

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Incoloy 800 Washer Specifications
Specifications : ASTM B408
Standard : DIN, ASTM, BS and all International Standards
Length : M02 to M33
Size : 3 mm to 200 mm
Type : Flat Washer, Lock Washer, Sealing Washer, Split Washer, Slot Washer, Machine Washer, Star Washer SPRINGS – Wire Spring & Flat Spring
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Incoloy 800/800H/800HT Washers Chemical Composition
Grade C Mn Si S Cu Fe Ni Cr Al Ti
800 0.10 max 1.50 max 1.00 max 0.015 max 0.75 max 39.50 min 30.00 – 35.00 19.00 – 23.00 0.15 – 0.60 0.15 – 0.60
800H 0.05 – 0.10 1.50 max 1.00 max 0.015 max 0.75 max 39.50 min 30.00 – 35.00 19.00 – 23.00 0.15 – 0.60 0.15 – 0.60
800HT 0.06 – 0.10 1.50 max 1.00 max 0.015 max 0.75 max 39.50 min 30.00 – 35.00 19.00 – 23.00 0.15 – 0.60ᴬ 0.15 – 0.60ᴬ
Alloy 800/800H/800HT Washer Mechanical Properties
Element Density Melting Point Tensile Strength Yield Strength (0.2%Offset) Elongation
800 / 800H / 800HT 7.94 g/cm3 1385 °C (2525 °F) Psi – 75,000 , MPa – 520 Psi – 30,000 , MPa – 205 30 %
Equivalent Grades for Incoloy Alloy 800/800H/800HT Washer
STANDARD WERKSTOFF NR. UNS JIS BS GOST AFNOR EN OR
Incoloy 800 1.4876 N08800 NCF 800 NA 15 ЭИ670 Z8NC32-21 X10NiCrAlTi32-20 XH32T
Incoloy 800H 1.4958 / 1.4876 N08810 NCF 800H NA 15(H) ЭИ670 Z8NC33-21 X5NiCrAlTi31-20 XH32T
Incoloy 800HT 1.4859 / 1.4876 N08811 NCF 800HT NA 15(HT) ЭИ670 X8NiCrAlTi32-21 XH32T
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Alloy 800/800H/800HT Washers Application Industries
  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry
800/800H/800HT Incoloy Washers Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and MacroTest
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

[/bt_text][/bt_column][/bt_row][bt_row][/bt_row][/bt_section]
By |2021-03-23T13:00:01+05:30March 23rd, 2021|

Inconel 718 Washers Manufacture

[bt_section][bt_row][bt_column width=”1/1″][bt_text]

 

Sachiya Steel International offers an extensive range and is a known supplier of Inconel 718 Washers, which can be readily machined in either the annealed or the age – hardened condition. Inconel 718 Flat Washers is hardened by the precipitation of secondary phases (e.g. gamma prime and gamma double – prime) into the metal matrix.

Inconel 718 Lock Washers maintains good corrosion resistance and oxidation resistance and is used for parts requiring high resistance to creep and stress rupture up to 1300 Degree F (704 Degree C). Inconel 718 Sealing Washers is used in a variety of industries such as aerospace, marine engineering, chemical processing, pollution – control equipment, and nuclear reactors.

Inconel 718 Washers | Inconel 718 Washers | Inconel 718 Washers | Inconel 718 Washers | Inconel 718 Washers 

Inconel 718 Split Washers is also used in Gas Turbines, Space Craft, Rocket Motors, Pumps and so on. In both as – built and age – hardened states, the parts of these Inconel 718 Slot Washers can be machined, spark – eroded, welded, micro shot – peened, coated and polished if required.

The excellent strength and corrosion resistance of Inconel 718 Machine Washers have been recognized by the oil industry and it is now widely used in this field. It is the optimum heat treatment for these Inconel 718 Star Washers where a combination of rupture life, rupture ductility and notch rupture life is required. The age-hardening response of Inconel 718 Spring Washers permits the annealing and welding without spontaneous hardening during heating and cooling.

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Inconel 718 Washer Specifications
Specifications : ASTM B637
Standard : DIN, ASTM, BS and all International Standards
Length : M02 to M33
Size : 3 mm to 200 mm
Type : Flat Washer, Lock Washer, Sealing Washer, Split Washer, Slot Washer, Machine Washer, Star Washer SPRINGS – Wire Spring & Flat Spring
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Inconel 718 Washers Chemical Composition
Grade C Mn Si S Cu Fe Ni Cr
Inconel 718 0.08 max 0.35 max 0.35 max 0.015max 0.30 max 50.00 – 55.00 17.00 – 21.00
Alloy 718 Washer Mechanical Properties
Element Density Melting Point Tensile Strength Yield Strength (0.2%Offset) Elongation
Inconel 718 8.2 g/cm3 1350 °C (2460 °F) Psi – 1,35,000 , MPa – 930 Psi – 75,000 , MPa – 482 45 %
Equivalent Grades for Inconel Alloy 718 Washer
STANDARD WERKSTOFF NR. UNS JIS BS GOST AFNOR EN
Inconel 718 2.4668 N07718
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Alloy 718 Washers Application Industries
  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry
718 Inconel Washers Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]

Material Testing


We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Inconel 718 Washers
inconel 718 washer 500x500 1

Sachiya Steel International offers an extensive range and is a known supplier of Inconel 718 Washers, which can be readily machined in either the annealed or the age – hardened condition.

Product Brand: Sachiya Steel International

Product In-Stock: InStock

Editor's Rating:
5
[/bt_text][/bt_column][/bt_row][/bt_section]
By |2021-03-20T12:07:14+05:30March 20th, 2021|

Inconel 625 Washers Manufacture

[bt_section][bt_row][bt_column width=”1/1″][bt_text]

 

Sachiya Steel International is a known manufacturer of Inconel 625 Washers, which resists a wide range of severely corrosive environments and is especially resistant to pitting and crevice corrosion. Inconel 625 Flat Washer is often used in spray bars, turbine shroud rings, bellows and heat – exchanger tubing in environmental control systems.

Inconel 625 Lock Washer is non – magnetic and immune to chloride ion stress corrosion cracking, where they form in a needle – like morphology and are incoherent with the matrix. The nickel and chromium content in Inconel 625 Sealing Washers provide resistance to oxidizing environments. Inconel Alloy 625 Split Washer is also used in Flue gas desulfurization scrubbers and Weld Overlay.

Inconel 625 Washers | Inconel 625 Washers | Inconel 625 Washers | Inconel 625 Washers | Inconel 625 Washers

Inconel 625 Slot Washers is as well used in is used in chemical processing, marine engineering, aerospace, pollution – control equipment, nuclear reactor applications and so on. The oxidation and scaling resistance of Alloy 625 Machine Washers is superior to a number of heat resistant austenitic stainless steels such as in Grade 304, Grade 309, Grade 310 and Grade 347 up to 1800 Degree F (982 Degree C) and under cyclic heating and cooling conditions.

Inconel Alloy 625 Star Washer has high resistance to oxidation at elevated temperatures up to 1050 Degree C, which is also supplied in the hot worked and annealed condition. These Inconel 625 Spring Washers is a nickel – chromium – molybdenum – niobium alloy with excellent resistance to a variety of corrosive media.

 

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Inconel 625 Washer Specifications
Specifications : ASTM B446
Standard : DIN, ASTM, BS and all International Standards
Length : M02 to M33
Size : 3 mm to 200 mm
Type : Flat Washer, Lock Washer, Sealing Washer, Split Washer, Slot Washer, Machine Washer, Star Washer SPRINGS – Wire Spring & Flat Spring
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Inconel 625 Washers Chemical Composition
Grade C Mn Si S Cu Fe Ni Cr
Inconel 625
0.10max 0.50 max 0.50 max 0.015max 5.0 max 58.0 min 20.0 – 23.0
Alloy 625 Washer Mechanical Properties
Element Density Melting Point Tensile Strength Yield Strength (0.2%Offset) Elongation
Inconel 625
8.4 g/cm3 1350 °C (2460 °F) Psi – 1,35,000 , MPa – 930 Psi – 75,000 , MPa – 517 42.5 %
Equivalent Grades for Inconel Alloy 625 Washer
STANDARD WERKSTOFF NR. UNS JIS BS GOST AFNOR EN
Inconel 625
2.4856 N06625 NCF 625 NA 21 ХН75МБТЮ NC22DNB4M NiCr22Mo9Nb
[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Alloy 625 Washers Application Industries
  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry
625 Inconel Washers Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Material Testing


We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

 

[/bt_text][/bt_column][/bt_row][bt_row][bt_column width=”1/1″][bt_text]
Inconel 625 Washers
inconel 625 washers 500x500 1

Sachiya Steel International is a known manufacturer of Inconel 625 Washers, which resists a wide range of severely corrosive environments and is especially resistant to pitting and crevice corrosion.

Product Brand: Sachiya Steel International

Product In-Stock: InStock

Editor's Rating:
5
[/bt_text][/bt_column][/bt_row][/bt_section]
By |2021-03-20T11:55:18+05:30March 20th, 2021|
Go to Top