LOGO 1200 X 300

Stainless Steel 317 Screw Manufacturers In India

By |2025-01-09T15:07:32+05:30March 9th, 2022|Screw|

Stainless Steel 317 Screw Manufacturers In India

Sachiya Steel International is one of the Leading Manufacturer And Exporter Of High Quality Stainless Steel 317 Screw, which can be successfully welded by all standard methods, where preheating is not necessary. Properties of Stainless Steel 317 Hex Head Screws comparable to those of the parent metal may be achieved in the weld metal by post – weld heat treatment. As for other high strength steels, precaution should be taken in design and welding procedures of these Stainless Steel 317 Socket Head Cap Screws to avoid concentration of weldment stresses.

Stainless Steel 317 Screw

After solution treatment a single low temperature “age hardening” treatment is employed to achieve required properties of Stainless Steel 317 Socket Set Screws. Heat treatment in these Stainless Steel 317 Anchors Screws results in no distortion and only superficial discoloration, where a slight decrease in size (shrinkage) takes place during the hardening. In solution treated, Stainless Steel 317 Blind Rivet has lower resistance to stress corrosion cracking, and lower ductility compared to aged conditions.

These Stainless Steel 317 Concrete Screws should not generally be used in the solution treated condition, even if the hardness is considered satisfactory. Stainless Steel 317 Threaded Screws has good oxidation resistance, but to avoid reduction of its mechanical properties and hardness it should not be used above its age hardening temperature. The great benefit of these Stainless Steel 317 Steel Shoulder Screws is that they are generally supplied in the solution treated condition.

Stainless Steel 317 Screw Specifications
Specifications : ASTM A 193 ASME SA 193
Standard : IS, ASTM, BS and all International Standards
Length : 3 mm to 200 mm
Size : M3 – M33
Type : Hex Head Screw, Socket Head Cap Screw, Socket Set Screws, Anchor Screw, Blind Rivet, Concrete screw, Threaded Screw, Steel Shoulder Screw, Panel Screw, Machine Screw.

317 Stainless Steel Screw Chemical Composition

Grade C Mn Si P S Cr Mo Ni N
317 min. – – – – – 18.0 – 11.0 –
max. 0.8 2.0 1.00 0.040 0.03 20.0 14.0 –

Stainless Steel 317 Screw Mechanical Properties

Grade Tensile Strength (MPa) min Yield Strength 0.2% Proof (MPa) min Elongation (% in 50mm) min Hardness
Rockwell B (HR B) max Brinell (HB) max
317 515 205 35 95 217

Stainless Steel 317 Screw Physical Properties

Grade Density (kg/m3) Elastic Modulus (GPa) Mean Coefficient of Thermal Expansion (m/m/0C) Thermal Conductivity (W/m.K) Specific Heat 0-1000C (J/kg.K) Electrical Resistivity (n.m)
0-1000C 0-3150C 0-5380C at 1000C at 5000C
317 8000 193 17.2 17.8 18.4 16.2 21.5 500 720

Equivalent Grades for 317 Stainless Steel Screw

Grade UNS No Old British Euronorm Swedish SS Japanese JIS
BS En No Name
317 S31700 – – 1.4449 – – –

SS 317 Screws Application Industries

Off-Shore Oil Drilling Companies
Power Generation
Petrochemicals
Gas Processing
Specialty Chemicals
Pharmaceuticals
Pharmaceutical Equipment
Chemical Equipment
Sea Water Equipment
Heat Exchangers
Condensers
Pulp and Paper Industry

317 Steel Screws Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

Stainless Steel 316Ti Screw Manufacturers In India

By |2025-01-09T15:05:48+05:30March 9th, 2022|Screw|

Stainless Steel 316Ti Screw Manufacturers In India

Sachiya Steel International is one of the Leading Manufacturer And Exporter Of High Quality Stainless Steel 316Ti Screw, which is characterized by its corrosion resistance, especially in cases of oxidation and salt water. Stainless Steel 316Ti Hex Head Screws is a stainless steel with applications ranging from the manufacturing of chemical equipment, kitchen and cooking utensils and equipment, to surgical tools and textile dyeing equipment. Stainless Steel 316Ti Socket Head Cap Screws is the most commonly utilized grade of stainless steel, being extremely versatile in application, form, and finishes.

Stainless Steel 316Ti Screw

Stainless Steel 316Ti Socket Set Screws is considered the basic stainless – steel alloy, composed of 18 % chromium and 8 % nickel, where these components also give causes that are to be referred to as “18 / 8”. The remainder of the composition of Stainless Steel 316Ti Anchors is made up of carbon, manganese, silicon and very small amounts of phosphorous and Sulphur. This makeup ensures that Stainless Steel 316Ti Blind Rivet has a well – balanced level of performance in terms of weldability, corrosion resistance and anti – oxidation properties.

Additionally, Stainless Steel 316Ti Concrete Screws is pliable under both hot and cold working, though it responds better to cold working; it will only work harden under cold working. Stainless Steel 316Ti Threaded Screws is extended exposure to temperatures between the ranges of 800 Degree F – 1500 Degree F that can lead to embrittlement and should be carefully monitored.

SS 316Ti Screws Specifications
Specifications : ASTM A 193 ASME SA 193
Standard : IS, ASTM, BS and all International Standards
Length : 3 mm to 200 mm
Size : M3 – M33
Type : Hex Head Screw, Socket Head Cap Screw, Socket Set Screws, Anchor Screw, Blind Rivet, Concrete screw, Threaded Screw, Steel Shoulder Screw, Panel Screw, Machine Screw.

316Ti Stainless Steel Screw Chemical Composition

Grade C Mn Si P S Cr Mo Ni N
316Ti min. – – – – – 16.0 2.00 10.0 –
max. 0.08 2.0 0.75 0.045 0.030 18.0 3.00 14.0 –

Stainless Steel 316Ti Screw Mechanical Properties

Grade Tensile Strength (MPa) min Yield Strength 0.2% Proof (MPa) min Elongation (% in 50mm) min Hardness
Rockwell B (HR B) max Brinell (HB) max
316Ti 515 205 35 75 205

Stainless Steel 316Ti Screw Physical Properties

Grade Density (kg/m3) Elastic Modulus (GPa) Mean Coefficient of Thermal Expansion (m/m/0C) Thermal Conductivity (W/m.K) Specific Heat 0-1000C (J/kg.K) Electrical Resistivity (n.m)
0-1000C 0-3150C 0-5380C at 1000C at 5000C
316Ti 8000 193 17.2 17.8 18.4 16.2 21.5 500 720

Equivalent Grades for 316Ti Stainless Steel Screw

Grade UNS No Old British Euronorm GOST Japanese JIS
BS En No AFNOR
316Ti S31635 320S31 X6CrNiMoTi17-12-2 1.4571 Z6CNDT17‐12 08Ch17N13M2T SUS 316Ti

SS 316Ti Screws Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

316Ti Steel Screws Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

Titanium Gr 5 Nuts Manufacturers In India

By |2025-01-09T16:46:38+05:30March 3rd, 2022|Fasteners|

Titanium Gr 5 Nuts Manufacturers In India

Sachiya Steel International is one of the Leading Manufacturer And Exporter Of High Quality Titanium Gr 5 Nuts And Bolts, which has good creep resistance up to approx. 300 Degree C (570 Degree F). We are able to machine Titanium Grade 5 Hex Head Bolts, besides the fact it was the first to process this material with the technology of Rapid Casting. Designing with Titanium Grade 5 Hex Head Nuts taking all factors into account has resulted in reliable, economic and more durable systems and components, which in many situations have substantially exceeded performance and service life expectations.

Titanium Gr 5 Nuts

Titanium Grade 5 Square Bolts had excellent strength to weight ratio and also higher strength at ambient temperatures than Grades 1 and 2. Titanium Grade 5 Square Nuts has outstanding resistance to corrosion in most natural and many industrial process environments, with approximately half the density of nickel alloys. Titanium’s high corrosion resistance is also a valuable characteristic; as when exposed to the atmosphere, Titanium Grade 5 Eye Bolts forms a tight, tenacious oxide film that resists many corrosive materials, particularly salt water.

Titanium Grade 5 Eye Nuts is produced by primary melting using vacuum arc (VAR), electron beam (EB), or plasma arc hearth melting (PAM). Titanium Grade 5 T-Bolts is often used with the goal to get really close to the final dimensions of the part being made. Its usability lies in its many benefits, where Titanium Grade 5 T-Nuts may be heat treated to increase its strength.

Titanium Alloy Grade 5 Bolt/Nut Specifications
Specifications : ASTM B 348 ASME SB 348
Standard : DIN, ASTM, BS and all International Standards
Length : 3 mm to Gr 5 mm
Size : M3 – M56 | 3/6″ to 2″ | Custom Sizes
Type : Hex Head Bolts, Square Bolts, U bolts, Eye bolts, T bolt, Hex Bolt, Lag Bolts, Counter sunk Bolts, Hex Head nuts, Square nuts, Lock nuts, Eye nuts, wing nuts, T nuts, Panel Nuts, Coupling Nuts, Dome nuts, Acorn Nuts.

Gr 5 Titanium Alloy Bolt/Nut Chemical Composition

Titanium Gr 5 C Ti N Fe H O V Al
0.10 max 90 min 0.05 max 0.40 max 0.015 max 0.20 max 3.5-4.5 5.5-6.75 max

Titanium Alloy Gr 5 Bolt/Nut Mechanical Properties

Density Melting Point Yield Strength (0.2%Offset) Tensile Strength Elongation
4.43 g/cm3 1632 °C (2970 °F) Psi – 128000 , MPa – 880 Psi – 138000 , MPa – 950 14 %

Equivalent Grades for Gr 5 Titanium Bolt/Nut

STANDARD UNS WERKSTOFF NR.
Titanium Gr 5 R56400 3.7165

Ti. Alloy Gr 5 Bolt/Nut Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Grade 5 Titanium Alloy Bolt/Nut Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

Titanium Gr 2 Nuts Manufacturers In India

By |2025-01-09T16:43:43+05:30March 3rd, 2022|Fasteners|

Titanium Gr 2 Nuts Manufacturers In India

Sachiya Steel International is one of the Leading Manufacturer And Exporter Of High Quality Titanium Gr 2 Nuts And Bolts , which is sometimes referred to as “Commercial Pure (CP)” due to its approximate yield strength. Designing with these Titanium Grade 2 Hex Head Bolts taking all factors into account has resulted in reliable, economic and more durable systems and components, which in many situations have substantially exceeded performance and service life expectations. Our Titanium Grade 2 Hex Head Nuts possesses the greatest formability, excellent corrosion resistance and high impact toughness.

Titanium Gr 2 Nuts

Continuous service temperatures for these Titanium Grade 2 Square Bolts can reach up to 800 Degree F with occasional, intermittent service at 1000 Degree F. Hold at 1103 Degree F to 1400 Degree F (595 Degree C to 760 Degree C) for two hours, then Air cool and Stress relive our Titanium Grade 2 Square Nuts by holding at 1004 Degree F to 1103 Degree F (540 Degree C to 595 Degree C) for 15 minutes to 30 minutes.

However, the high cost of these Titanium Grade 2 Eye Bolts and processing limit their use to military applications, aircraft, spacecraft, and medical devices. Our Titanium Grade 2 Eye Nuts is light weight and highly corrosion resistant, but has much lower strength than alpha – beta or beta titanium alloys. These Titanium Grade 2 T-Bolts should be emphasized that fabrication operations (annealing, descaling) can increase the impurity level unless particular care is taken.

Titanium Grade 2 Bolt/Nut Specifications
Specifications : ASTM B 348 ASME SB 348
Standard : DIN, ASTM, BS and all International Standards
Length : 3 mm to Gr 2 mm
Size : M3 – M56 | 3/6″ to 2″ | Custom Sizes
Type : Hex Head Bolts, Square Bolts, U bolts, Eye bolts, T bolt, Hex Bolt, Lag Bolts, Counter sunk Bolts, Hex Head nuts, Square nuts, Lock nuts, Eye nuts, wing nuts, T nuts, Panel Nuts, Coupling Nuts, Dome nuts, Acorn Nuts.

Gr 2 Titanium Alloy Bolt/Nut Chemical Composition

Titanium Gr 2 C Ti N Fe H O V Al
0.1 max 99.2 min 0.03 max 0.3 max 0.015 max 0.25 max – –

Titanium Alloy Gr.2 Bolt/Nut Mechanical Properties

Density Melting Point Yield Strength (0.2%Offset) Tensile Strength Elongation
4.5 g/cm3 1665 °C (3030 °F) Psi – 39900 , MPa – 275 Psi – 49900 , MPa – 344 20 %

Equivalent Grades for Grade 2 Titanium Bolt/Nut

STANDARD UNS WERKSTOFF NR.
Titanium Gr 2 R50400 3.7035

Ti. Alloy Gr 2 Bolt/Nut Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Grade 2 Titanium Alloy Bolt/Nut Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

Carbon Steel Nuts Manufacturers In India

By |2025-01-08T12:33:19+05:30March 1st, 2022|Fasteners|

Carbon Steel Nuts Manufacturers In India

Sachiya Steel International is one of the Leading Manufacturer And Exporter Of High Quality Carbon Steel Nuts And Bolts, which have shown good formability in a variety of fabrications. Carbon Steel Counter Sunk Bolts has excellent general corrosion resistance; superior to Grade 316 in most environments, where higher cutting forces are required and more rapid tool wear is typical. Carbon Steel Acorn Nuts has excellent resistance to localized corrosion including inter – granular, pitting and crevice corrosion, where the CPT is generally at least 35 Degree C. Carbon Steel Lag Bolts is also resistant to chloride stress corrosion cracking (SCC) at temperatures of up to about 150 Degree C.

Carbon Steel Nuts

Sachiya Steel International is one of the prominent distributor and stockiest for high quality ASME SA 563 Carbon Steel Dome Nuts, which is similar to Type 904, but has more strength and hardness. Carbon Steel Hex Bolts can be hardened through heat treatment, which brings good ductility for metal fabricators as well as excellent polish ability.

Application of Carbon Steel Coupling Nuts could result in real cost savings when carefully compared to higher – cost alloys to determine if the necessary resistance is obtained in the chosen media. Carbon Steel T-Bolts has excellent resistance to general corrosion, pitting, and crevice corrosion in chemicals containing chlorides and sulphuric, phosphoric, and nitric acids.

Carbon Steel Nuts/Bolts Specifications
Specifications : ASTM A 307 ASME SA 307 / ASTM A 563 ASME SA 563
Standard : DIN, ASTM, BS and all International Standards
Length : 3 mm to 200 mm
Size : M3 – M56 | 3/6″ to 2″ | Custom Sizes
Type : Hex Head Bolts, Square Bolts, U bolts, Eye bolts, T bolt, Hex Bolt, Lag Bolts, Counter sunk Bolts, Hex Head nuts, Square nuts, Lock nuts, Eye nuts, wing nuts, T nuts, Panel Nuts, Coupling Nuts, Dome nuts, Acorn Nuts.

Carbon Steel Bolt/Nut Chemical Composition

Element Carbon, max Manganese, max Phosphorus, max Sulfur, max
Grade A 0.29 % 1.20 % 0.04 % 0.15 %
Grade B 0.29 % 1.20 % 0.04 % 0.05 %

Carbon Steel Bolt/Nut Mechanical Properties

Grade Tensile, ksi Yield, min, ksi Elong %, min
A 60 min — 18
B 60 – 100 — 18
C* 58 – 80 36 23

Carbon Steel Bolt/Nut Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Carbon Steel Bolt/Nut Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

Nickel Alloy 201 Nuts Manufacturers In India

By |2025-01-08T16:38:56+05:30March 1st, 2022|Fasteners|

Nickel Alloy 201 Nuts Manufacturers In India

Sachiya Steel International is one of the Leading Manufacturer And Exporter Of High Quality Nickel Alloy 201 Nuts And Bolts, where annealing should be performed in a reducing atmosphere to retain bright finishes. These Nickel 201 Hex Head Bolts has been found that 0.25 % moisture in hydrogen chloride did not affect corrosion rate in both wet and dry gas at 400 Degree F (205 Degree C). Annealing of our Nickel 201 Hex Head Nuts for periods of 1 hour or more at temperatures above 1700 Degree F (925 Degree C) will result in hardness. Heat treatment for these Nickel 201 Square Bolts, commonly called a dead – soft anneal, is used only in specialized applications such as burst diaphragms because of the low mechanical properties and coarse grain structure produced.

Nickel Alloy 201 Nuts Manufacturer

Dry hydrogen and dissociated ammonia are preferred for our Nickel 201 Square Nuts, but less expensive atmospheres like partially burned natural gas will also provide adequate brightness. Heating in oxidizing atmospheres for these Nickel 201 Eye Bolts at high temperatures should be avoided because of the danger of inter – granular oxidation.

Our Nickel 201 Eye Nuts is sensitive to inter – granular attack from Sulphur and metals such as lead, tin, zinc, and bismuth that have low melting points. Scrupulous care must be exercised in these Nickel 201 Hex Bolts to remove all traces of forming lubricants, marking paints and shop soil prior to heating.

Nickel Alloy 201 Nuts/Bolts Specifications
Specifications : ASTM B 164 ASME SB 164
Standard : DIN, ASTM, BS and all International Standards
Length : 3 mm to 201 mm
Size : M3 – M56 | 3/6″ to 2″ | Custom Sizes
Type : Hex Head Bolts, Square Bolts, U bolts, Eye bolts, T bolt, Hex Bolt, Lag Bolts, Counter sunk Bolts, Hex Head nuts, Square nuts, Lock nuts, Eye nuts, wing nuts, T nuts, Panel Nuts, Coupling Nuts, Dome nuts, Acorn Nuts.

201 Nickel Alloy Bolt/Nut Chemical Composition

Nickel 201 Ni C Mo Mn Si Fe P S Cu Cr
Balance 0.15 max – 0.35 max 0.35 max 0.40 max – 0.01 max 0.25 max –

Nickel Alloy 201 Bolt/Nut Mechanical Properties

Density Melting Point Yield Strength (0.2%Offset) Tensile Strength Elongation
8.9 g/cm3 1446 °C (2635 °F) Psi – 21500 , MPa – 148 Psi – 67000 , MPa – 462 45 %

Equivalent Grades for 201 Nickel Bolt/Nut

STANDARD UNS WERKSTOFF NR. AFNOR EN JIS BS GOST
Nickel 201 N02201 2.4068 – LC-Ni 99 NW 2201 NA 12 НП-2

Alloy 201 Bolt/Nut Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

201 Nickel Alloy Bolt/Nut Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

Alloy Steel 2H Nuts Manufacturers In India

By |2024-02-10T13:57:02+05:30February 21st, 2022|Fasteners|

Sachiya Steel International is one Of The Leading Manufacturer And Exporter Of High Quality Alloy Steel 2H Nuts And Bolts where is very soluble in ferrite; therefore, it forms compounds. Riding on unfathomable volumes of industrial expertise, we are engaged in offering an outstanding variety of Alloy Steel Grade 2H Hex Head Bolts. We are also recognized as the distinguished trader and supplier of superior quality gamut of these Alloy Steel Grade 2H Hex Head Nuts that find wide usage in various industries. The provided Alloy Steel Grade 2H Square Bolts are used in different industrial applications in the industries like chemicals, fats, & fertilizers.

Alloy Steel 2H Nuts

Constructed from premium grade raw materials, our range of these Alloy Steel Grade 2H Square Nuts is known for high – strength, excellent finish and longer life. Available in different dimensions & specifications, Alloy Steel Grade 2H Eye Bolts are widely used in different industries like power, engineering, construction and many more.

These Alloy Steel Grade 2H Eye Nuts are also often used in earthling, electrification lines, transformers, artificial imitation jewelry, anodes, bus bars, gaskets, auto radiators, cable wrap, transformer core and rectifiers, heat exchangers, etc. Concentrating on success that we have acquired in the market remains our status as famous trader, exporter and supplier of a precision – designed Alloy Steel Grade 2H T-Bolts, because we are also a renowned trader, exporter and supplier of the same.

Alloy Steel 2H Bolts/Nut Specifications
Specifications : ASTM A 194 ASME SA 194
Standard : DIN, ASTM, BS and all International Standards
Length : 3 mm to 2H mm
Size : M3 – M56 | 3/6″ to 2″ | Custom Sizes
Type : Hex Head Bolts, Square Bolts, U bolts, Eye bolts, T bolt, Hex Bolt, Lag Bolts, Counter sunk Bolts, Hex Head nuts, Square nuts, Lock nuts, Eye nuts, wing nuts, T nuts, Panel Nuts, Coupling Nuts, Dome nuts, Acorn Nuts

2H Alloy Steel Bolt/Nut Chemical Composition

Alloy Steel 2 C Mn P S Si Ni Cr
0.40% min 1.00% max 0.040% 0.050% 0.40% max – –

Mechanical Properties

Specification Material Nominal Size, In. Tempering Temp. °F Proof Load Stress, ksi Hardness Rockwell See Note
Min Max
ASTM A194 Grade 2H Medium Carbon Steel, Quenched and Tempered 1/4 – 4 1000 175 C24 C38 1,2

Alloy Steel 2H Bolt/Nut Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

2H Alloy Steel Bolt/Nut Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

Alloy Steel GR 6 Nuts Manufacturers In India

By |2024-02-15T12:50:12+05:30February 21st, 2022|Fasteners|

Alloy Steel GR 6 Nuts Manufacturers In India

Sachiya Steel International is one of the Leading Manufacturer And Exporter Of High Quality Alloy Steel GR 6 Nuts And Bolts, which can be customizing according to client’s end uses & specification. Vanadium, titanium, and niobium in Alloy Steel Grade 6 Hex Head Bolts are strong carbide forming elements, forming vanadium carbide, titanium carbide, and niobium carbide, respectively. Alloy Steel Grade 6 Hex Head Nuts has some great features to provide our clients such as High durability, Perfect in dimension, Easy handling, High performance, Reasonable price and more.

Alloy Steel GR 6 Nuts

Capitalizing on the skills of our dedicated team of professionals, we are involved in providing Alloy Steel Grade 6 Square Bolts to our respected clients, which is light in weight and is of good quality. Alloy Steel Grade 6 Square Nuts are also widely acknowledged for their features like strength, chemical resistance and abrasion and corrosion resistance. Available in various specifications, Alloy Steel Grade 6 Eye Bolts offered by us is highly used in various industries.

The offered Alloy Steel Grade 6 Eye Nuts is used for fabricating different kinds of industrial, commercial as well as construction materials. We would like to take the opportunity to have a fruitful business co – operation with you & thus we would request you to kindly register our organization as an approved manufacturer for the supply of Alloy Steel Grade 6 T-Bolts by sending us your valuable inquiries or tenders for your future requirement.

Alloy Steel GR 6 Bolt/Nut Specifications
Specifications : ASTM A 194 ASME SA 194
Standard : DIN, ASTM, BS and all International Standards
Length : 3 mm to GR 6 mm
Size : M3 – M56 | 3/6″ to 2″ | Custom Sizes
Type : Hex Head Bolts, Square Bolts, U bolts, Eye bolts, T bolt, Hex Bolt, Lag Bolts, Counter sunk Bolts, Hex Head nuts, Square nuts, Lock nuts, Eye nuts, wing nuts, T nuts, Panel Nuts, Coupling Nuts, Dome nuts, Acorn Nuts.

GR 6 Alloy Steel Bolt/Nut Chemical Composition

Alloy Steel GR 6 C Mn P S Si Ni Cr
0.15% 1.00% 0.04% 0.03% 1.00% – 11.5-13.5%

Alloy Steel GR 6 Bolt/Nut Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

GR 6 Alloy Steel Bolt/Nut Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

Incoloy 800 Nuts Manufacturers In India

By |2025-01-08T12:58:40+05:30February 15th, 2022|Fasteners|

Incoloy 800 Nuts Manufacturers In India

Sachiya Steel International is one of the Leading Manufacturer And Exporter Of High Quality Incoloy 800 Nuts And Bolts, which is extremely resistant to corrosion and even in acidic environment. Because of its high nickel and chromium content, Incoloy 800 Hex Head Bolts resist oxidation and carburization at high temperatures. The chemical balance allows the Incoloy 800H Square Nuts to exhibit excellent resistance to carburization, oxidation and nitriding atmospheres. For the first time, aluminum and titanium were listed as purposeful additions, and annealed Incoloy 800HT U-Bolts was differentiated from solution – annealed material.

Incoloy 800 Nuts

Incoloy 800 Lock Nuts will not become embrittled even after long periods of usage in the 1200 Degree F – 1600 Degree F range where many stainless steels become brittle. The restricted chemical compositions, combined with the high temperature anneal, assure these materials have greater creep and rupture strength when compared to Incoloy 800H Eye Bolts. Many companies in a wide range of industries utilize Incoloy 800HT Wing Nuts for a number of applications, especially those that deal with temperatures about 1100 Degree F (600 Degree C).

Incoloy 800 T-Bolts is especially useful for high – temperature equipment in the petrochemical industry since the alloy doesn’t form the embrittling sigma phase after long time exposure at 1200 Degree F. Incoloy 800H Panel Bolts have nickel – chromium – iron as the base metals, with additives such as molybdenum, copper, silicon and nitrogen.

Alloy 800/800H/800HT Bolt/Nut Specifications
Specifications : ASTM B 408 ASME SB 408
Standard : DIN, ASTM, BS and all International Standards
Length : 3 mm to 200 mm
Size : M3 – M56 | 3/6″ to 2″ | Custom Sizes
Type : Hex Head Bolts, Square Bolts, U bolts, Eye bolts, T bolt, Hex Bolt, Lag Bolts, Counter sunk Bolts, Hex Head nuts, Square nuts, Lock nuts, Eye nuts, wing nuts, T nuts, Panel Nuts, Coupling Nuts, Dome nuts, Acorn Nuts.

800/ 800H/ 800HT Incoloy Alloy Bolt/Nut Chemical Composition

Grade C Mn Si Fe S Cr Al-Ti Ni
800 min. – – – 39.5 – 19.0 0.15 30.0
max. 0.1 1.5 1.0 – 0.015 23.0 0.60 35.0
800H min. 0.05 – – 39.5 – 19.0 0.15 30.0
max. 0.1 1.5 1.0 – 0.015 23.0 0.60 35.0
800HT min. 0.06 – – 39.5 – 19.0 0.85/0.25 30.0
max. 0.1 1.5 1.0 – 0.015 23.0 1.20/0.60 35.0

Incoloy Alloy 800/ 800H/ 800HT Bolt/Nut Mechanical Properties

Grade Tensile Strength (MPa) min Yield Strength 0.2% Proof (MPa) min Elongation (% in 50mm) min Hardness
Rockwell B (HR B) max Brinell (HB) max
800-H-HT Psi – 75,000 , MPa – 520 Psi – 30,000 , MPa –205 30 – –

Equivalent Grades for 800 / 800H / 800HT Incoloy Bolt/Nut

STANDARD WERKSTOFF NR. UNS JIS BS GOST AFNOR EN OR
Incoloy 800 1.4876 N08800 NCF 800 NA 15 ЭИ670 Z8NC32-21 X10NiCrAlTi32-20 XH32T
Incoloy 800H 1.4958 / 1.4876 N08810 NCF 800H NA 15(H) ЭИ670 Z8NC33-21 X5NiCrAlTi31-20 XH32T
Incoloy 800HT 1.4859 / 1.4876 N08811 NCF 800HT NA 15(HT) ЭИ670 – X8NiCrAlTi32-21 XH32T

Alloy 800/800H/800HT Bolt/Nut Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

800/800H/800HT Incoloy Bolt/Nut Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

Alloy 17-4 PH Nuts Manufacturers In India

By |2024-02-05T15:36:04+05:30February 11th, 2022|Fasteners|

Sachiya Steel International is one of the Leading Manufacturer And Exporter Of High Quality Alloy 17-4 PH Nuts And  Bolts, where short – time and low – temperature heat treatments minimize distortion and scaling. Typical usage of Alloy 17-4 PH Hex Head Bolts is seen in applications requiring high strength and a modest level of corrosion resistance. These Alloy 17-4 PH Hex Head Nuts can be heat treated to high levels of strength and hardness, and features corrosion resistance and machinability comparable to austenitic 304 stainless. The valuable combination of high strength, good corrosion resistance and toughness in Alloy 17-4 PH Hex Head Nuts over both base metals and welds gives designers opportunities to add reliability to their products while simplifying fabrication and often reducing costs.

Alloy 17-4 PH Nuts Manufacturer

To increase their yield strength, these Alloy 17-4 PH Square Bolts are subjected to heat treatment during precipitation hardening (PH) or age hardening. High strength of Alloy 17-4 PH Square Nuts is maintained to approximately 600 degrees Fahrenheit (316 degrees Celsius). These Alloy 17-4 PH Eye Bolts has adequate resistance to atmospheric corrosion or in diluted acid salts where its corrosion resistance is equivalent to Alloy 304 or Alloy 430.

Alloy 17-4 PH Eye Nuts combines high strength, hardness (up to 572 Degree F / 300 Degree C), and corrosion resistance. Known for its’ corrosion resistance characteristics, the different shapes and finishes of these Alloy 17-4 PH T-Bolts make the composition suitable for a wide variety of environments.

17-4ph Bolt/Nut Specifications
Specifications : ASTM A 479 ASME SA 479
Standard : DIN, ASTM, BS and all International Standards
Length : 3 mm to mm
Size : M3 – M56 | 3/6″ to 2″ | Custom Sizes
Type : Hex Head Bolts, Square Bolts, U bolts, Eye bolts, T bolt, Hex Bolt, Lag Bolts, Counter sunk Bolts, Hex Head nuts, Square nuts, Lock nuts, Eye nuts, wing nuts, T nuts, Panel Nuts, Coupling Nuts, Dome nuts, Acorn Nuts.

SS 17-4ph Bolt/Nut Chemical Composition

SS 17-4ph Ni C Mo Mn Si S Cr
3.00 – 5.00 0.07 0.60 1.50 0.70 0.015 15.0 – 17.0

SS 17-4ph Bolt/Nut Mechanical Properties

Density Melting Point Yield Strength (PSI)
 Tensile Strength (PSI) Elongation
7.8
 1425 °C
 170 190 10 %

17-4ph Bolt/Nut Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

17-4ph Bolt/Nut Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 104/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 104 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 104/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 104 3.1 and EN 104 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

LOGO 1200 X 300

D-2, Office No 3, Bharat Nagar CHS, Near Shalimar Cinema,
Grant Road ( East ) , Mumbai- 40007, Maharashtra, India.

[email protected]
[email protected]

OUR PRODUCTS

ACCREDITATION

certified stamp

© Copyright - 2026 | Sachiya Steel International | All Rights Reserved | Terms & Conditions | Privacy Policy | Sitemap

Go to Top