Sachiya Steel International

astm a182 standard pdf manufacturer

Alloy Steel F91 Socket Weld Fittings Manufacturer

Sachiya Steel International is one of the Leading Manufacturer And Exporter of High Quality Alloy Steel F91 Socket Weld Fittings, which resists high temperature embrittlement better than other grades but the effect will still occur after about 10 hours at elevated temperatures. Although our Alloy Steel F91 Forged Socket Weld Elbow Fittings has good high temperature oxidation resistance this grade, like other stainless steels, suffers from embrittlement if held at temperatures above 300 Degree C. We have been able to provide first class quality products of these Alloy Steel F91 Forged Socket Weld Tee Fittings to a large number of clients in the global market.

Our Alloy Steel F91 Forged Socket Weld Cross Fittings contains a minimum of 11.5 % chromium which is just sufficient enough to demonstrate corrosion resistance properties in mild atmospheres, steam, and many mild chemical environments. These Alloy Steel F91 Forged Socket Weld Cap Fittings is a general purpose grade that is often supplied in the hardened but still machinable condition for applications where high strength and moderate heat and corrosion resistance are required.

If our Alloy Steel F91 Forged Socket Weld Coupling Fittings undergoes substantial deformation, then it should undergo a re – anneal or stress – relieving treatment at about 1202 Degree F (650 Degree C). These Alloy Steel F91 Forged Socket Weld Union Fittings can be used in environments containing weak or diluted acetic acid, naphtha, nitric acid and sulphuric acid.

Alloy Steel F91 Forged Socket weld Fittings Specifications
Specifications : ASTM A182 & ASME SA182
Size : 1/2″ NB TO 48″ NB.
Standards
 : ASME 16.11, MSS SP-79, 83, 95, 97, BS 3799
Class : 2000 LBS, 3000 LBS, 6000 LBS, 9000 LBS
Type : Socket weld Fittings

Alloy Steel F91 Forged Socket weld Fittings Chemical Composition

Grade C Mn Si S P Cr Mo
Alloy Steel F91 0.08-0.12 0.3-0.6 0.5 0.01 0.02 8.5-9.5 0.85-1.05

Alloy Steel Grade F91 Socket weld Fitting Mechanical Properties

Tensile Strength Yield Strength (0.2%Offset) Elongation
415 585 20 %

Alloy Steel F91 Forged Socket weld Fittings Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Alloy Steel F91 Forged Socket weld Fittings Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2023-11-25T17:49:42+05:30October 15th, 2021|

Alloy Steel F22 Socket Weld Fittings Manufacturer

Sachiya Steel International is one of the Leading Manufacturer And Exporter of High Quality Alloy Steel F22 Socket Weld Fittings, which remains magnetic in both the annealed and heat treated conditions. Our clients are our most valuable assets and for that we use our skilled people and latest technology and equipment’s for to make these Alloy Steel F22 Forged Socket Weld Elbow Fittings to fulfil their needs. In the annealed condition, our Alloy Steel F22 Forged Socket Weld Tee Fittings is ductile and may possibly be formed. These Alloy Steel F22 Forged Socket Weld Cross Fittings is resistant to atmospheric conditions, water and some chemicals.

We are a proactive organization and also a specialist in our Alloy Steel F22 Forged Socket Weld Cap Fittings and other quality products that meet and exceed customer`s specific requirements and as a result we ensure complete satisfaction. Our management style has been the key to our success in making these Alloy Steel F22 Forged Socket Weld Coupling Fittings, as we delegates responsibility to the specific need of every customers and we have made every customer a member of our family.

Elevated mechanical properties and corrosion resistance are being achieved with our Alloy Steel F22 Forged Socket Weld Union Fittings when it’s hardened and tempered. These Alloy Steel F22 Forged Socket Weld Plug Fittings can be used in applications such as dental and surgical instruments, pipelines, valves and nozzles, automotive parts and more.

Alloy Steel F22 Forged Socket weld Fittings Specifications
Specifications : ASTM A182 & ASME SA182
Size : 1/2″ NB TO 48″ NB.
Standards
 : ASME 16.11, MSS SP-79, 83, 95, 97, BS 3799
Class : 2000 LBS, 3000 LBS, 6000 LBS, 9000 LBS
Type : Socket weld Fittings

Alloy Steel F22 Forged Socket weld Fittings Chemical Composition

Grade C Mn Si S P Cr Mo
Alloy Steel F22 0.05-0.15 0.3-0.6 0.5 0.03 0.045 0.8-1.25 0.44-0.65

Alloy Steel Grade F22 Socket weld Fitting Mechanical Properties

Tensile Strength Yield Strength (0.2%Offset) Elongation
205 415 20 %

Alloy Steel F22 Forged Socket weld Fittings Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Alloy Steel F22 Forged Socket weld Fittings Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2023-11-25T15:18:59+05:30October 14th, 2021|

Alloy Steel F12 Socket Weld Fittings Manufacturer

Sachiya Steel International is one of the Leading Manufacturer And Exporter of High Quality Alloy Steel F12 Socket Weld Fittings, which is available in personalized and also in different designs and sizes to our clients. The crevice corrosion resistance of Alloy Steel F12 Forged Socket Weld Elbow Fittings can be in excess of that of the 6 % Mo grades in some cases. Copper content in Alloy Steel F12 Forged Socket Weld Tee Fittings adds resistance to sulphuric and other reducing acids, particularly in the very aggressive “mid concentration” range. We are a renowned name in this domain engaged in providing Alloy Steel F12 Forged Socket Cap Elbow Fittings.

We have gained immense client`s appreciation for Alloy Steel F12 Forged Socket Weld Cross Fittings, owing to our excellent product quality and transparent dealings. For maximum corrosion resistance to chemical environments, Alloy Steel F12 Forged Socket Weld Coupling Fittings is essential that the stainless steel surface be free of all heat tints or oxide formed during forging, annealing, or heat treating.

All surfaces of Alloy Steel F12 Forged Socket Weld Union Fittings must be ground or polished to remove any traces of oxide and surface decarburization. The parts of Alloy Steel F12 Forged Socket Weld Plug Fittings should then immerse in a warm solution of 10 % – 20 % nitric acid to remove any residual iron, where a thorough water rinse should follow the nitric acid treatment.

Alloy Steel F12 Forged Socket weld Fittings Specifications
Specifications : ASTM A182 & ASME SA182
Size : 1/2″ NB TO 48″ NB.
Standards
 : ASME 16.11, MSS SP-79, 83, 95, 97, BS 3799
Class : 2000 LBS, 3000 LBS, 6000 LBS, 9000 LBS
Type : Socket weld Fittings

Alloy Steel F12 Forged Socket weld Fittings Chemical Composition

Grade C Mn Si S P Cr Mo
Alloy Steel F12 0.15 max 0.3-0.6 0.5 0.03 0.03 4-6 0.44-0.65

Alloy Steel Grade F12 Socket weld Fitting Mechanical Properties

Tensile Strength Yield Strength (0.2%Offset) Elongation
275 485 20 %

Alloy Steel F12 Forged Socket weld Fittings Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Alloy Steel F12 Forged Socket weld Fittings Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2023-11-25T13:12:19+05:30October 14th, 2021|

Alloy Steel F11 Socket Weld Fittings Manufacturer

Sachiya Steel International is one of the Leading Manufacturer And Exporter of High Quality Alloy Steel F11 Socket Weld Fittings, which must be hardened for maximum heat and corrosion resistance. Performance of Alloy Steel F11 Forged Socket Weld Elbow Fittings is best with a smooth surface finish. Alloy Steel F11 Forged Socket Weld Tee Fittings has less corrosion resistance than the austenitic grades and also less than 17 % chromium ferritic alloys. We have great pleasure to introduce ourselves as one of the leading Stockist & Suppliers of Alloy Steel F11 Forged Socket Weld Cap Fittings. For thin sections of Alloy Steel F11 Forged Socket Weld Cross Fittings, air cooling can be substituted for the oil quench.

As a result, Alloy Steel F11 Forged Socket Weld Coupling Fittings still exhibits its high hardness and wears resistance properties but some ductility is introduced at the loss of a few pints of hardness. Characterized by good corrosion resistance in mild atmospheric industrial and domestic environments, Alloy Steel F11 Forged Socket Weld Union Fittings is coupled with good strength and excellent toughness in the hardened and tempered condition.

Due to its excellent hardenability, Alloy Steel F11 Forged Socket Weld Plug Fittings is capable of being through hardened depending upon carbon content and section size. Alloy Steel F11 Forged Socket Weld Lateral Tee Fittings is rated as more resistant than grade 904L and approaching that of the 6 % Molybdenum “super austenitic” grades.

Alloy Steel F11 Forged Socket weld Fittings Specifications
Specifications : ASTM A182 & ASME SA182
Size : 1/2″ NB TO 48″ NB.
Standards
 : ASME 16.11, MSS SP-79, 83, 95, 97, BS 3799
Class : 2000 LBS, 3000 LBS, 6000 LBS, 9000 LBS
Type : Socket weld Fittings

Alloy Steel F11 Forged Socket weld Fittings Chemical Composition

Grade C Mn Si S P Cr Mo
Alloy Steel F11 0.05-0.15 0.3-0.6 0.5-1 0.03 0.03 1-1.5 0.044-0.65

Alloy Steel Grade F11 Socket weld Fitting Mechanical Properties

Tensile Strength Yield Strength (0.2%Offset) Elongation
205 415 20 %

Alloy Steel F11 Forged Socket weld Fittings Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Alloy Steel F11 Forged Socket weld Fittings Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2023-11-25T12:50:43+05:30October 13th, 2021|

Alloy Steel F9 Socket Weld Fittings Manufacturer

Sachiya Steel International is one of the Leading Manufacturer And Exporter of High Quality Alloy Steel F9 Socket Weld Fittings, which is sometimes used in the unhardened or hardened and highly tempered condition because of its low cost and ready machinability. Use of this Alloy Steel F9 Forged Socket Weld Elbow Fittings, if post hardening and tempering is involved. In the hardened and tempered as supplied condition, Alloy Steel F9 Forged Socket Weld Tee Fittings is not recommended due to its effect on the mechanical properties within the heat affected zone.

Alloy Steel F9 Forged Socket Weld Cross Fittings have better corrosion resistance, where it is also lower than most of the ferrite stainless steels, and all of the 300 series austenitic stainless steels. Alloy Steel F9 Forged Socket Weld Cap Fittings has optimum corrosion resistance in the hardened and tempered condition and is not therefore recommended for use in the annealed condition.

Alloy Steel F9 Forged Socket Weld Coupling Fittings is most important that oxygen is always allowed to circulate freely on all stainless steel surfaces to ensure that a chrome oxide film is always present to protect it. We are capable of providing a vast range of materials like Alloy Steel F9 Forged Socket Weld Union Fittings from stock, to suit your needs. Alloy Steel F9 Forged Socket Weld Plug Fittings resists dry atmosphere, fresh water, mild alkalis and acids, food, steam and hot gases.

Alloy Steel F9 Forged Socket weld Fittings Specifications
Specifications : ASTM A182 & ASME SA182
Size : 1/2″ NB TO 48″ NB.
Standards
 : ASME 16.11, MSS SP-79, 83, 95, 97, BS 3799
Class : 2000 LBS, 3000 LBS, 6000 LBS, 9000 LBS
Type : Socket weld Fittings

Alloy Steel F9 Forged Socket weld Fittings Chemical Composition

Grade C Mn Si S P Cr Mo
Alloy Steel F9 0.15 0.3-0.6 0.5-1 0.03 0.03 8-10 0.9-1.1

Alloy Steel Grade F9 Socket weld Fitting Mechanical Properties

Tensile Strength Yield Strength (0.2%Offset) Elongation
380 585 20 %

Alloy Steel F9 Forged Socket weld Fittings Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Alloy Steel F9 Forged Socket weld Fittings Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2023-11-25T17:01:53+05:30October 13th, 2021|

Alloy Steel F1 Socket Weld Fittings Manufacturer

Sachiya Steel International is one of the Leading Manufacturer And Exporter of High Quality Alloy Steel F1 Socket Weld Fittings, which is commonly used for cutlery – particularly blades of table knives and for some carving knives and similar. On completion of welding in our Alloy Steel F1 Forged Socket Weld Elbow Fittings, cool slowly as possible until hand warm and as required. Carry out post – weld sub – critical anneal of these Alloy Steel F1 Forged Socket Weld Tee Fittings at 630 Degree C – 680 Degree C or full anneal and harden and temper as required.

Our Alloy Steel F1 Forged Socket Weld Cap Fittings does not work hardens to the same extent as the 300 series austenitic stainless steels, but is more similar in this respect to the low alloy high tensile steels.  These Alloy Steel F1 Forged Socket Weld Cross Fittings has less corrosion resistant than the austenitic grades and also less than 17 % chromium ferrite alloys, which further also have slightly lower resistance.

The corrosion resistance of our Alloy Steel F1 Forged Socket Weld Coupling Fittings is sufficient to resist food and normal washing methods, but prolonged contact with unwashed food residues can result in pitting. Always ensure that the tempering temperature employed during the initial heat treatment in these Alloy Steel F1 Forged Socket Weld Union Fittings was higher than the nitriding temperature otherwise the core strength will be affected.

Alloy Steel F1 Forged Socket weld Fittings Specifications
Specifications : ASTM A182 & ASME SA182
Size : 1/2″ NB TO 48″ NB.
Standards
 : ASME 16.11, MSS SP-79, 83, 95, 97, BS 3799
Class : 2000 LBS, 3000 LBS, 6000 LBS, 9000 LBS
Type : Socket weld Fittings

Alloy Steel F1 Forged Socket weld Fittings Chemical Composition

Grade C Mn Si S P Cr Mo
Alloy Steel F1 0.15 max 0.3-0.6 0.5 0.03 0.03 4-6 0.44-0.65

Alloy Steel Grade F1 Socket weld Fitting Mechanical Properties

Tensile Strength Yield Strength (0.2%Offset) Elongation
275 485 20 %

Alloy Steel F1 Forged Socket weld Fittings Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Alloy Steel F1 Forged Socket weld Fittings Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2023-11-25T12:31:45+05:30October 12th, 2021|

Alloy Steel F91 Threaded Forged Fittings Manufacturers In India

Sachiya Steel International is one of the leading Manufacturer And Exporter of Alloy Steel F91 Threaded Forged Fittings, which is not recommended for use in temperatures above the relevant tempering temperature, because of reduction in mechanical properties. Our Alloy Steel F91 Forged Threaded Elbow Fittings has highly resistant to stress corrosion cracking if aged at 550 Degree C or higher, where higher aging temperatures give better SCC resistance. Heat this Alloy Steel F91 Forged Threaded Tee Fittings uniformly up to 1200 Degree F / 1400 Degree F (650 Degree C / 760 Degree C) along with air cool.

For maximum softness, heat this Alloy Steel F91 Forged Threaded Cross Fittings up to 1500 Degree F / 1650 Degree F (815 Degree C / 900 Degree C) along with slow furnace cool. Temper this Alloy Steel F91 Forged Threaded Cap Fittings at temperatures appropriate to produce desired mechanical properties. If this Alloy Steel F91 Forged Threaded Coupling Fittings is tempered in the range 750 Degree F / 1050 Degree F (400 Degree C / 565 Degree C), there will be a decrease in impact strength and in corrosion resistance – depending upon the media.

Alloy Steel F91 Threaded Forged Fittings

The tempering range 425 Degree C – 600 Degree C in this Alloy Steel F91 Forged Threaded Bend Fittings should be avoided. Meanwhile, the scaling temperature of our Alloy Steel F91 Forged Threaded Bushing Fittings should be approximately temperature of 650 Degree C.

Alloy Steel F91 Threaded Forged Fittings Specifications
Specifications : ASTM A182 & ASME SA182
Size : 1/2″ NB TO 48″ NB.
Standards
 : ASME 16.11, MSS SP-79, 83, 95, 97, BS 3799
Class : 2000 LBS, 3000 LBS, 6000 LBS, 9000 LBS
Type : Threaded Forged Fittings

Alloy Steel F91 Threaded Forged Fittings Chemical Composition

Grade C Mn Si S P Cr Mo
Alloy Steel F91 0.08-0.12 0.3-0.6 0.5 0.01 0.02 8.5-9.5 0.85-1.05

Alloy Steel Grade F91 Threaded Forged Fitting Mechanical Properties

Tensile Strength Yield Strength (0.2%Offset) Elongation
415 585 20 %

Alloy Steel F91 Threaded Forged Fittings Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Alloy Steel F91 Threaded Forged Fittings Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2024-02-06T12:12:19+05:30September 15th, 2021|Threaded Forged Fittings|

Alloy Steel F22 Threaded Forged Fittings Manufacturer

Sachiya Steel International is one of the Leading Manufacturer And Exporter of Alloy Steel F22 Threaded Forged Fittings, which has reasonably good cold working properties and can be moderately drawn and formed in the annealed condition. Because of the wide range of widths and thicknesses and the variety of tempers produced in our Alloy Steel F22 Forged Threaded Elbow Fittings and cut lengths, no flatness tolerances have been established for cold rolled stainless steel.

Flatness on temper rolled in these Alloy Steel F22 Forged Threaded Tee Fittings cannot be guaranteed. This aging treatment in our Alloy Steel F22 Forged Threaded Cross Fittings is so low in temperature that there is no significant distortion. These Alloy Steel F22 Forged Threaded Cap Fittings are therefore well suited to production of long shafts, which require no re – straightening after heat treatment. Parts of our Alloy Steel F22 Forged Threaded Coupling Fittings should be preheated at 350 Degree F / 400 Degree F (180 Degree C / 205 Degree C) to prevent cracking, particularly in heavy sections.

Since these Alloy Steel F22 Forged Threaded Bend Fittings is air hardening, parts should be annealed immediately after welding. Our Alloy Steel F22 Forged Threaded Union Fittings are therefore well suited to production of long shafts, which require no re – straightening after heat treatment. For better machinability, these Alloy Steel F22 Forged Threaded Bushing Fittings reduces annealing temperature to give higher hardness.

Alloy Steel F22 Threaded Forged Fittings Specifications
Specifications : ASTM A182 & ASME SA182
Size : 1/2″ NB TO 48″ NB.
Standards
 : ASME 16.11, MSS SP-79, 83, 95, 97, BS 3799
Class : 2000 LBS, 3000 LBS, 6000 LBS, 9000 LBS
Type : Threaded Forged Fittings

Alloy Steel F22 Threaded Forged Fittings Chemical Composition

Grade C Mn Si S P Cr Mo
Alloy Steel F22 0.05-0.15 0.3-0.6 0.5 0.03 0.045 0.8-1.25 0.44-0.65

Alloy Steel Grade F22 Threaded Forged Fitting Mechanical Properties

Tensile Strength Yield Strength (0.2%Offset) Elongation
205 415 20 %

Alloy Steel F22 Threaded Forged Fittings Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Alloy Steel F22 Threaded Forged Fittings Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2023-11-25T15:23:28+05:30September 14th, 2021|

Alloy Steel F12 Threaded Forged Fittings Manufacturer

Sachiya Steel International is one of the leading manufacturer and exporter of Alloy Steel F12 Threaded Forged Fittings, which provides valuable property combinations peculiarly well suited for aerospace applications. In high – heat treated conditions, these Alloy Steel F12 Forged Threaded Elbow Fittings possesses excellent mechanical properties. Our Alloy Steel F12 Forged Threaded Tee Fittings also provides benefits for other applications requiring high strength and good corrosion resistance – by means of excellent properties at temperatures up to 600 Degree F.

These Alloy Steel F12 Forged Threaded Cross Fittings requires three steps in heat treating including austenite conditioning, cooling to transform the austenite to martensitic, and precipitation hardening. This addition in our Alloy Steel F12 Forged Threaded Cap Fittings is made to reduce or eliminate chromium carbide precipitation – resulting from welding or exposure to high temperatures. These Alloy Steel F12 Forged Threaded Bend Fittings in its cold rolled, hardened and tempered condition is used in countless applications similar to Cold Rolled High Carbon but with the advantages inherent in being excellent alloy and at moderate cost.

Our Alloy Steel F12 Forged Threaded Coupling Fittings in its pre – hardened condition is stocked by us in coils ready for slitting to exact widths for press feed operations or to exact size blanks. These Alloy Steel F12 Forged Threaded Bend Fittings are just machinable, and then can be age hardened to achieve quite high strengths.

Alloy Steel F12 Threaded Forged Fittings Specifications
Specifications : ASTM A182 & ASME SA182
Size : 1/2″ NB TO 48″ NB.
Standards
 : ASME 16.11, MSS SP-79, 83, 95, 97, BS 3799
Class : 2000 LBS, 3000 LBS, 6000 LBS, 9000 LBS
Type : Threaded Forged Fittings

Alloy Steel F12 Threaded Forged Fittings Chemical Composition

Grade C Mn Si S P Cr Mo
Alloy Steel F12 0.15 max 0.3-0.6 0.5 0.03 0.03 4-6 0.44-0.65

Alloy Steel Grade F12 Threaded Forged Fitting Mechanical Properties

Tensile Strength Yield Strength (0.2%Offset) Elongation
275 485 20 %

Alloy Steel F12 Threaded Forged Fittings Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Alloy Steel F12 Threaded Forged Fittings Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

Material Testing 

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2023-11-25T13:15:28+05:30September 14th, 2021|

Alloy Steel F11 Threaded Forged Fittings Manufacturer

Sachiya Steel International is one of the leading manufacturer and exporter of Alloy Steel F11 Threaded Forged Fittings, which have good creep and oxidation resistance. However, Alloy Steel F11 Forged Threaded Elbow Fittings is not fully stain – proof in low-oxygen, high – salinity, or poor air – circulation environments. We are one of the renowned trader and suppliers of Alloy Steel F11 Forged Threaded Tee Fittings which is a high – chromium alloy having excellent resistance to many corrosive aqueous media and high temperature atmospheres. The resistance of Alloy Steel F11 Forged Threaded Cross Fittings in Nitric acid plus hydrofluoric acid mixtures lends itself to pickle shop duties.

Alloy Steel F11 Forged Threaded Coupling Fittings is also known as high performance alloys, and can be formed in different shapes. In addition to its corrosion resistance, Alloy Steel F11 Forged Threaded Cap Fittings has high strength, good metallurgical stability and favorable fabrication characteristics. The high chromium content gives Alloy Steel F11 Forged Threaded Cross Fittings excellent resistance to aqueous corrosion by oxidizing acids (especially nitric acid) and salts and to suffixation at high – temperatures.

Alloy Steel F11 Forged Threaded Bend Fittings is a precipitation hardened steel that provides high strength and hardness, excellent fatigue properties, good corrosion resistance, good formability, and minimum distortion upon heat treatment. The formability of Alloy Steel F11 Forged Threaded Union Fittings is good for its yield strength and hardness range.

Alloy Steel F11 Threaded Forged Fittings Specifications
Specifications : ASTM A182 & ASME SA182
Size : 1/2″ NB TO 48″ NB.
Standards
 : ASME 16.11, MSS SP-79, 83, 95, 97, BS 3799
Class : 2000 LBS, 3000 LBS, 6000 LBS, 9000 LBS
Type : Threaded Forged Fittings

Alloy Steel F11 Threaded Forged Fittings Chemical Composition

Grade C Mn Si S P Cr Mo
Alloy Steel F11 0.05-0.15 0.3-0.6 0.5-1 0.03 0.03 1-1.5 0.044-0.65

Alloy Steel Grade F11 Threaded Forged Fitting Mechanical Properties

Tensile Strength Yield Strength (0.2%Offset) Elongation
205 415 20 %

Alloy Steel F11 Threaded Forged Fittings Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Alloy Steel F11 Threaded Forged Fittings Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2023-11-25T12:54:18+05:30September 13th, 2021|

SACHIYA STEEL INTERNATIONAL

D-2, Office No 3, Bharat Nagar CHS, Near Shalimar Cinema,
Grant Road ( East ) , Mumbai- 40007, Maharashtra, India.

[email protected]
[email protected]

OUR PRODUCTS

ACCREDITATION

certified stamp

© Copyright - 2024 | Sachiya Steel International | All Rights Reserved | Terms & Conditions | Privacy Policy | Sitemap

Go to Top