LOGO 1200 X 300

Wire

Nickel Alloy 200 Wire Manufacturers In India

Sachiya Steel International is One Of The Leading Manufacturer And Exporter Of High Quality Nickel Alloy 200 Wire, where chlorine additives would be an alternative. Nickel 200 Coil Wire is a Nickel based alloy containing 47.5 % Nickel, 22 % Chromium and 18.5 % Iron, with small amounts of Cobalt, Molybdenum and Tungsten. All hot – or cold – worked parts of Nickel 200 Wire should be annealed and rapidly cooled in order to restore the best balance of properties. Carbide tools in Nickel 200 Wire should have smaller angles than high – speed tools and operating speeds can be higher. After 100 hours in petroleum coke, Nickel 200 is completely penetrated by carburization; whereas its specimens showed no carburization at all.

Nickel Alloy 200 Wire

Useful Properties for Aircraft and Furnace Parts, Nickel 200 Wire is recommended especially for use in furnace applications. Alloy 200 Wire has unusual resistance to oxidizing, reducing, and neutral atmospheres, where work hardening occurs whenever a tool makes a cut. Its uncommon resistance to oxidation, combined with exceptional heat resistance and fabricability, make Alloy 200 a widely sought – after blend in a number of industries.

Thoroughly clean work piece after machining Alloy 200 Coil Wire, is to prevent surface contamination during subsequent heat treating. Because of the low thermal conductivity in Alloy 200 Wire, heat build – up is a problem, and therefore, correct coolant application is necessary.

Nickel 200 Wire Specifications
Specifications : ASTM B160 ASME SB160
Dimensions : ANSI/AWCI – 01 -1992 and ASTM E 2016-11 and RRW 360
Length : 100 mm TO 6000 mm
Diameter : 10 mm To 100 mm
Specialize : Filler Wire, Coil Wire, Electrode Wire, Welding Wire.

200 Nickel Wire Chemical Composition

Grade C Mn Si Cu S Cr Fe Ni N
Nickel 200 0.15 max 0.35 max 0.35 max 0.25 max 0.01 max – 0.40 max 99.0 min –

Nickel 200 Wire Mechanical Properties

Element Density Melting Point Tensile Strength Yield Strength (0.2%Offset) Elongation
Nickel 200  8.9 g/cm3  1446 °C (2635 °F) Psi – 67000 , MPa – 462 Psi – 21500 , MPa – 148 45 %

Equivalent Grades for 200 Nickel Wire

STANDARD WERKSTOFF NR. UNS JIS BS GOST AFNOR EN
Nickel 200 2.4066 N02200 NW 2200 NA 11 НП-2 N-100M Ni 99.2

Nickel 200 Wire Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

200 Nickel Wire Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2024-02-01T16:33:25+05:30May 7th, 2022|Wire|

Monel Alloy K500 Wire Manufacturers In India

Sachiya Steel International is One Of The Leading Manufacturer And Exporter Of High Quality Monel Alloy K500 Wire, which is a low alloy pressure vessel quality steel for high temperatures. Monel K500 Wire is primarily used in welded pressure vessels where improved toughness is required. Monel K500 Welding Wire is a metal alloy consisting mostly of iron, in addition to small amounts of carbon, depending on the grade and quality of the steel. Monel K500 Coil Wire is any type of steel to which one or more elements besides carbon have been intentionally added, to produce a desired physical property or characteristic. Common elements that are added to make Monel K500 are molybdenum, manganese, nickel, silicon, boron, chromium, and vanadium.

Monel Alloy K500 Wire

These metals are added to produce specific properties for Monel K500 that is not found in regular carbon steel. Alloy K500 Filler Wire is normally used in the annealed temper, and strength characteristics described below are representative of annealed material. Alloy K500 should be machined by the procedures, where the usual annealing temperature is approximately 1900 Degree F (1040 Degree C).

Like other nickel alloys, Alloy K500 Coil Wire should be clean before it is heated and should be heated in a low – Sulphur atmosphere. In various types of high – temperature water, Alloy K500 Welding Wire displays low corrosion rates and excellent resistance to stress – corrosion cracking.

Monel K500 Wire Specifications
Specifications : ASTM B865 ASME SB865
Dimensions : ANSI/AWCI – 01 -1992 and ASTM E 2016-11 and RRW 360
Length : 100 mm TO 6000 mm
Diameter : 10 mm To 100 mm
Specialize : Filler Wire, Coil Wire, Electrode Wire, Welding Wire.

K500 Monel Wire Chemical Composition

Grade C Mn Si Cu S Cr Fe Ni N
Monel K500  0.25 max 1.50 max  0.50 max 27.0-33.0 0.10max  – 0.5-2.0 max 63.00 min  –

Monel K500 Wire Mechanical Properties

Element Density Melting Point Tensile Strength Yield Strength (0.2%Offset) Elongation
Monel K500  8.44 g/cm3  1350 °C (2460 °F)  Psi – 1,60,000 , MPa – 1100 Psi – 115000 , MPa – 790 20%

Equivalent Grades for K500 Monel Wire

STANDARD WERKSTOFF NR. UNS JIS BS GOST AFNOR EN
Monel K500 2.4375 N05500

Monel K500 Wire Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

K500 Monel Wire Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2024-02-02T10:56:34+05:30May 7th, 2022|Wire|

Monel Alloy 400 Wire Manufacturers In India

Sachiya Steel International is One Of The Leading Manufacturer And Exporter Of High Quality Monel Alloy 400 Wire , which is in fact used most commonly in high temperature brazing applications. Our Monel 400 Wire is generally being used when specifications call for corrosion resistance and high – temperature service properties. This Monel 400 Coil Wire can also be used in sub – zero applications as low as the temperature of liquid oxygen, helium, or nitrogen. Nickel brazing alloys have low vapour pressure, making our Monel 400 Welding Wire suited to vacuum systems and vacuum tube applications.

Monel Alloy 400 Wire

With their joint strength and resistance to corrosion, this nickel brazing Monel 400 Electrode is ideal for jet engine parts and assemblies, food handling equipment, nuclear energy and carbide tools. Our Monel 400 Welding can only be hardened by further rolling, while showing excellent corrosion resistance, which is higher than that of pure nickel in reduced environments and better than that of copper in oxidizing environments.

This Alloy 400 Electrode is a solid solution alloy that can be hardened by the process of cold working. Our Alloy 400 Filler Wire is also known as super alloy, where series of nickel – copper alloys are grouped. The proportions of copper and nickel used to make this Alloy 400 Welding Wire are the same as that found in the nickel ore found in Ontario mines.

Monel 400 Wire Specifications
Specifications : ASTM B164 ASME SB164
Dimensions : ANSI/AWCI – 01 -1992 and ASTM E 2016-11 and RRW 360
Length : 100 mm TO 6000 mm
Diameter : 10 mm To 100 mm
Specialize : Filler Wire, Coil Wire, Electrode Wire, Welding Wire.

400 Monel Wire Chemical Composition

Grade C Mn Si Cu S Cr Fe Ni N
Monel 400  0.30 max 2.00 max  0.50 max 28.0-34.0 0.24max  – 2.50 max 63.00 min  –

Monel 400 Wire Mechanical Properties

Element Density Melting Point Tensile Strength Yield Strength (0.2%Offset) Elongation
Monel 400  8.8 g/cm3  1350 °C (2460 °F)  Psi – 80,000 , MPa – 550 Psi – 35,000 , MPa – 240 40%

Equivalent Grades for 400 Monel Wire

STANDARD WERKSTOFF NR. UNS JIS BS GOST AFNOR EN
Monel 400 2.4360 N04400 NCF 400 NA 13 МНЖМц 28-2,5-1,5 NU-30M NiCu30Fe

Monel 400 Wire Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

400 Monel Wire Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2024-02-02T11:11:41+05:30May 6th, 2022|Wire|

Hastelloy X Wire Manufacturers In India

Sachiya Steel International is One Of The Leading Manufacturer And Exporter Of High Quality Hastelloy X Wire which is known for its excellent high temperature strength withstanding up to 2200 Degree F. Hastelloy X Wire can also be easily fabricated with forming and welding characteristics by both manual and automatic methods. Our Hastelloy X Coil Wire offers exceptional performance in furnace rolls or other industrial furnace applications because of the alloy’s strong resistance to oxidizing, reducing and neutral atmospheres. In addition, Hastelloy X Wire is widely used for a variety of chemical processing parts, including retorts, pyrolysis tubing, and muffles due to its exceptional resistance to stress – corrosion cracking.

Hastelloy X Wire

Our Hastelloy X wire is normally supplied in the solution – treated condition, following a treatment at 2150 Degree F (1175 Degree C) and rapid cooling. Bright annealed parts of Hastelloy X Wire are cooled in hydrogen, where high – speed steel or cast – alloy tools are recommended. The machinability rating of our Alloy X Coil Wire is 27 %, where slow speeds, positive feeds and rigid equipment are the order of the day.

Alloy X Wire has low hardness, good ductility and good weldability, making the metal easy to fabricate. Our Alloy X Wire has a low work – hardening rate, but it may be cold worked to moderately high strength levels while maintaining ductility.

Hastelloy X Wire Specifications
Specifications : AMs 5754 AMS 5798
Dimensions : ANSI/AWCI – 01 -1992 and ASTM E 2016-11 and RRW 360
Length : 100 mm TO 6000 mm
Diameter : 10 mm To 100 mm
Specialize : Filler Wire, Coil Wire

X Hastelloy Wire Chemical Composition

Grade C Mn Si Co P Fe Mo Ni Cr S
Hastelloy X 0.05 – 0.15 1.00 max 1.00 max 0.50 – 2.50 0.04 max 17.00 – 20.00 8.00 – 10.00 Balance 20.50 – 23.00 0.03 max

Hastelloy X Wire Mechanical Properties

Density Melting Point Yield Strength (0.2%Offset) Tensile Strength Elongation
8.22 g/cm3 1355 °C   MPa – 665  MPa – 240 35 %

Equivalent Grades for X Hastelloy Wire

STANDARD WERKSTOFF NR. UNS JIS EN
Hastelloy X 2.4665 N06002

Hastelloy X Wire Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

X Hastelloy Wire Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2024-02-02T11:14:34+05:30May 6th, 2022|Wire|

Inconel 601 Wire Manufacturers In India

Sachiya Steel International is One Of The Leading Manufacturer And Exporter Of High Quality Inconel 601 Wire, which develops a tightly adherent oxide scale which resists spalling even under severe thermal cycling. Other applications of our Inconel 601 Wires include thermocouple protection tubes, condenser tubes, process heaters, and so on. This Inconel 601 Wire is best forged, for large deformations, between 2250 Degree F and 1900 Degree F, but forging may be continued to 1650 Degree F. Due to high chromium and some aluminum content in our Inconel 601 Coil Wire, good resistance in oxidizing sulfur bearing atmospheres at elevated temperatures is demonstrated.

Inconel 601 Wire

This Inconel 601 Electrode is often used in Chemical Processing, Heat treating industry, Aerospace, Power generation and so on. Our Inconel 601 Wire is a standard material of construction for various types of thermal – processing equipment. This Inconel 601 Wire has good creep rupture strength, along with readily joined by conventional welding products and processes.

Our Alloy 601 Wire can be machined using conventional machining methods which are used for iron – based alloys. This Alloy 601 Coil Wire is not suggested for use in strongly reducing and sulfur bearing environments. Our Alloy 601 Wire is a Nickel – Chromium alloy with an addition of Aluminum for outstanding resistance to oxidation and other forms of high temperature corrosion. This Alloy 601 Wire also has high mechanical properties at elevated temperatures.

Inconel 601 Wire Specifications
Specifications : ASTM B166 ASME SB166
Dimensions : ANSI/AWCI – 01 -1992 and ASTM E 2016-11 and RRW 360
Length : 100 mm TO 6000 mm
Diameter : 10 mm To 100 mm
Specialize : Filler Wire, Coil Wire

601 Inconel Wire Chemical Composition

Grade C Mn Si Cu S Cr Fe Ni N
Inconel 601  0.10 max 1.00 max 0.50 max  1.00 max 0.015max 21.00 – 25.00 bal  58.0-63.0  –

Inconel 601 Wire Mechanical Properties

Density Melting Point Tensile Strength Yield Strength (0.2%Offset) Elongation
8.1 g/cm3 1411 °C (2571 °F)  Psi – 80,000 , MPa – 550 Psi – 30,000 , MPa – 205 30 %

Equivalent Grades for 601 Inconel Wire

STANDARD WERKSTOFF NR. UNS JIS BS GOST AFNOR EN
Inconel 601 2.4851 N06601 NCF 601 NA 49 XH60BT NC23FeA NiCr23Fe

Inconel 601 Wire Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

601 Inconel Wire Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2024-02-02T11:19:57+05:30April 29th, 2022|Wire|

Inconel Alloy 600 Wire Manufacturers In India

Sachiya Steel International is One Of The Leading Manufacturer And Exporter Of High Quality Inconel Alloy 600 Wire, which are normally preferred for handling concentrated and high temperature caustic. Its high nickel content, a minimum of Ni 72 %, combined with its chromium content, provides users of Inconel 600 Wire a number of benefits. In strong oxidizing solutions like hot, concentrated nitric acid, Inconel 600 Coil Wire has poor resistance. The high chromium content of Inconel 600 Wire raises its oxidation resistance considerably above that of pure nickel, while its high nickel content provides good corrosion resistance under reducing conditions.

Inconel Alloy 600 Wire

Inconel 600 Wire can both hot formed and cold form using typical processes, and is also often used in vegetable and fatty acid vessels. Inconel 600 Wire is also used for furnace components, in food and chemical processing, nuclear engineering, and sparking electrodes. Chromium content in Alloy 600 Coiled Wire confers resistance to sulfur compounds and also provides resistance to oxidizing conditions at high temperatures or in corrosive solutions.

The high nickel content in Alloy 600 Coil Wire enables it to retain considerable resistance under reducing conditions. Alloy 600 Wire is a nickel – chromium alloy with good oxidation resistance at high temperatures and resistance to chloride – ion stress – corrosion cracking, corrosion by high – purity water, and caustic corrosion. Alloy 600 Wire has exceptional Temperature Resistance and Corrosion Resistance as its excellent properties.

Inconel 600 Wire Specifications
Specifications : ASTM B166 ASME SB166
Dimensions : ANSI/AWCI – 01 -1992 and ASTM E 2016-11 and RRW 360
Length : 100 mm TO 6000 mm
Diameter : 10 mm To 100 mm
Specialize : Filler Wire, Coil Wire

600 Inconel Wire Chemical Composition

Grade C Mn Si Cu S Cr Fe Ni N
Inconel 600  0.15 max 1.00 max 0.50 max  0.50 max 0.015max 14.00 – 17.00 6.00 – 10.00  72.00 min  –

Inconel 600 Wire Mechanical Properties

Element Density Melting Point Tensile Strength Yield Strength (0.2%Offset) Elongation
Inconel 600 8.47 g/cm3 1413 °C (2580 °F) Psi – 95,000 , MPa – 655 Psi – 45,000 , MPa – 310 40 %

Equivalent Grades for 600 Inconel Wire

STANDARD WERKSTOFF NR. UNS JIS BS GOST AFNOR EN
Inconel 600 2.4816 N06600 NCF 600 NA 13 МНЖМц 28-2,5-1,5 NC15FE11M NiCr15Fe

Inconel 600 Wire Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

600 Inconel Wire Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2024-02-02T11:24:31+05:30April 29th, 2022|Wire|

Stainless Steel 321 Wire Manufacturers In India

Sachiya Steel International is One Of The Leading Manufacturer And Exporter Of High Quality Stainless Steel 321 Wire, which is used for heating and is extremely low in Sulphur. This Stainless Steel 321 Wire must be absolutely clean and free from all oil, paint, grease, and shop soil when charged into the furnace. The furnace atmosphere for forging or open annealing in our Stainless Steel 321 Wire should be slightly reducing, containing at least 2 % of carbon monoxide. A slight positive pressure should be maintained in the furnace of this Stainless Steel 321 Coil Wire to prevent air infiltration.

Stainless Steel 321 Wire

When our Stainless Steel 321 Wire is heated in a reducing atmosphere, a thin, adherent green – black film of oxide will be left on the surface of the material. In heating for hot working, this Stainless Steel 321 Wire should be brought up to temperature, allowed to soak a short time to ensure uniformity, and withdrawn. In oxidizing atmospheres of our Stainless Steel 321 Wire, a heavy black scale is produced that is very difficult to remove.

Every precaution should be taken in heating this 321 Stainless Steel Wire so that only the green – black film is formed. There is excellent resistance in our 321 Stainless Steel Wire, which is similar to that of other nickel – chromium alloys, is a function of its composition.

SS 321 Wire Specifications
Specifications : ASTM A580 ASME SA580 / ASTM A313 ASME SA313
Dimensions : ASTM, ASME
Length : MAX 12000 mm
Diameter : 5.5 mm To 400 mm
Specialize : Wire, Coil Wire

321 Stainless Steel Wire Chemical Composition

Grade C Mn Si P S Cr Mo Ni N
SS 321 0.08 2.0 0.75 0.045 0.030 17.0-19.0 – 9.0-12.0 0.10

Stainless Steel 321 Wire Mechanical Properties

Grade Tensile Strength (MPa) min Yield Strength 0.2% Proof (MPa) min Elongation (% in 50mm) min Hardness
Rockwell B (HR B) max Brinell (HB) max
321 515 205 40 95 217

Equivalent Grades for 321 Stainless Steel Wire

Grade UNS No Old British Euronorm Swedish SS Japanese JIS
BS En No Name
321 S32100 321S31 58B, 58C 1.4541 X6CrNiTi18-10 2337 SUS 321

SS 321 Wire Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

321 Steel Wire Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2024-02-02T11:31:53+05:30April 25th, 2022|Wire|

Stainless Steel 317L Wire Manufacturers In India

Sachiya Steel International is One Of The Leading Manufacturer And Exporter Of High Quality Stainless Steel 317L Wire, which can be treated with heat; however, it will not respond. In addition to its higher carbon content, these Stainless Steel 317L Wires is stabilized with an addition of columbium, or sometimes tantalum. Both these properties allow Stainless Steel 317L Wires to be exposed to higher temperatures than other stainless steel grades that can withstand. Because of its elevated resistance to corrosion, these Stainless Steel 317L Coil Wires is often applied in high stress, high corrosion environments where exposure tends to be severe.

Stainless Steel 317L Wire

High temperature manufacturing, steam pipes, boiler tubes, chemical processes and steam servicing all benefit from resilience of Stainless Steel 317L Wire. This resilience in turn is due to the potentially elevated levels of chromium in composition of these Stainless Steel 317L Wire, where the metal can contain anywhere from 4 % – 30 %. Stainless Steel 317L Wires displays high workability under most common welding techniques. Only cold working is sufficient to increase these 317L Stainless Steel Wires toughness and strength.

317L Stainless Steel Wires may equal that of the 300 grades, but tends to display lower resistance to high temperature applications. However, these 317L Stainless Steel Wire displays resistance to both molten copper and molten brass, and is the only heat resistant alloy to do so.

SS 317L Wire Specifications
Specifications : ASTM A580 ASME SA580 / ASTM A313 ASME SA313
Dimensions : ASTM, ASME
Length : MAX 12000 mm
Diameter : 5.5 To 400 mm
Specialize : Wire, Coil Wire

317L Stainless Steel Wire Chemical Composition

Grade C Mn Si P S Cr Mo Ni N
SS 317L 0.035 max 2 max 1.0max 0.045 max 0.030 max 18 – 20 3.0-4.0 11.0-15.0 57.89 min

Stainless Steel 317L Wire Mechanical Properties

Grade Tensile Strength (MPa) min Yield Strength 0.2% Proof (MPa) min Elongation (% in 50mm) min Hardness
Rockwell B (HR B) max Brinell (HB) max
317L 515 205 35 75 205

Equivalent Grades for 317L Stainless Steel Wire

Grade UNS No Old British Euronorm Swedish SS Japanese JIS
BS En No Name
317L S31703 – X2CrNiMo18-15-4 1.4438 – – SUS 317L

SS 317L Wire Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

317L Steel Wire Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2024-02-02T11:42:21+05:30April 25th, 2022|Wire|
LOGO 1200 X 300

D-2, Office No 3, Bharat Nagar CHS, Near Shalimar Cinema,
Grant Road ( East ) , Mumbai- 40007, Maharashtra, India.

[email protected]
[email protected]

OUR PRODUCTS

ACCREDITATION

certified stamp

© Copyright - 2024 | Sachiya Steel International | All Rights Reserved | Terms & Conditions | Privacy Policy | Sitemap

Go to Top