LOGO 1200 X 300

Buttweld Fittings

Stainless Steel 317L Buttweld Fittings Manufacturer In India

Sachiya Steel International is one of the Leading Manufacture And Exporter of Stainless Steel 317L Buttweld Fittings, which have somewhat higher thermal conductivities than the austenitic grades, which may be an advantage in certain applications. This expansion coefficient not only varies Stainless Steel 317L Elbow it also increases slightly with temperature. Stainless Steel 317L Reducer Butt Weld Pipe Fittings has a coefficient over the temperature range Zero Degree C to 100 Degree C, but increases above this temperature. The effect of thermal expansion in Stainless Steel 317L Tee Butt Weld Pipe Fittings is most noticeable where components are restrained, as the expansion results in buckling and bending.

A problem can also arise if Stainless Steel 317L Cross Butt Weld Pipe Fittings are fabricated together and then heated, where dissimilar coefficients will again result in buckling or bending. In general, the quite high thermal expansion rates of the austenitic Stainless Steel 317L Bends mean that fabrications in these alloys may have more dimensional problems than similar fabrications in other alloy steels.

Localized stresses from expansion during heating and cooling of Stainless Steel 317L Stub End Butt Weld Pipe Fittings can contribute to stress corrosion cracking in an environment which would not normally attack the metal. These applications of Stainless Steel 317L End Cap require design to minimize the adverse effects of temperature differentials such as the use of expansion joints to permit movement without distortion and the avoidance of notches and abrupt changes of section.

Stainless Steel 317L Pipe Fittings Specifications
Specifications : ASTM A403 / ASME SA403
Size : 1/8” NB TO 48” NB. (Seamless & 100% X-Ray Welded, Fabricated)
Standards
 : ASME/ANSI B16.9, ASME B16.28, MSS-SP-43
Thickness : 5s, 10s, 40s, 80s, 10, 20, 40, STD, 60, 80, XS, 100, 120, 140, 160, XXS available with NACE MR 01-75
Type : Seamless / Welded / Fabricated

SS 317L Pipe Fittings Chemical Composition

Grade C Mn Si P S Cr Mo Ni Fe
SS 317L 0.035 max 2.0 max 1.0 max 0.045 max 0.030 max 18.00 – 20.00 3.00 – 4.00 11.00 – 15.00 57.89 min

Stainless Steel 317L Butt weld Fittings Mechanical Properties

Density Melting Point Tensile Strength Yield Strength (0.2%Offset) Elongation
7.9 g/cm3 1400 °C (2550 °F) Psi – 75000 , MPa – 515 Psi – 30000 , MPa – 205 35 %

Equivalent Grades for 317L Stainless Steel Pipe Fitting

STANDARD WERKSTOFF NR. UNS JIS BS GOST AFNOR EN
317L  1.4438 s31703      SUS 317L      –             –                –          X2CrNiMo18-15-4

SS WERKSTOFF NR.1.4438 Buttweld Pipe Fittings Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Stainless Steel 317L Buttweld Fitting Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2023-12-30T12:40:25+05:30July 27th, 2021|

Stainless Steel 321 Buttweld Fittings Manufacturer In India

Sachiya Steel International is a Leading Manufacture And Exporter Of a wide range of Stainless Steel 321 Buttweld Fittings, which is non-magnetic and offered in different sizes. This Stainless Steel 321 Butt Weld Fittings is often used in super-heater and afterburner parts, along with compensators and expansion bellows. Our Stainless Steel 321H Butt Weld Fittings is used extensively for applications where the addition of titanium and its stabilizing effect as a carbide forming element allows it to be welded and / or used within the carbide precipitation range 430 Degree C – 870 Degree C without the risk of inter-granular corrosion.

This Stainless Steel 321 Pipe Fittings is well known in reference literature and more information can be obtained in this way. Our Stainless Steel 321H Pipe Fittings is also used in refinery equipment and high temperature chemical process equipment. Titanium addition in this Stainless Steel 321 Elbow is made to reduce or eliminate chromium carbide precipitation – resulting from welding or exposure to high temperatures. Our Stainless Steel 321H Tee is as well used for heating element tubing and heat exchangers.

This Stainless Steel 321 Reducer is used extensively in the aircraft and missile industries. Our Stainless Steel 321H Cross is often used in Expansion joints and Pharmaceutical production. These Stainless Steel 321Bend is very resistant to oxidation and inter-granular corrosion up to 850 º C in dry air service conditions.

Stainless Steel 321/321H Pipe Fittings Specifications
Specifications : ASTM A403 / ASME SA403
Size : 1/8” NB TO 48” NB. (Seamless & 100% X-Ray Welded, Fabricated)
Standards
 : ASME/ANSI B16.9, ASME B16.28, MSS-SP-43
Thickness : 5s, 10s, 40s, 80s, 10, 20, 40, STD, 60, 80, XS, 100, 120, 140, 160, XXS available with NACE MR 01-75
Type : Seamless / Welded / Fabricated

SS 321/321H Pipe Fittings Chemical Composition

Grade C Mn Si P S Cr N Ni Ti
SS 321 0.08 max 2.0 max 1.0 max 0.045 max 0.030 max 17.00 – 19.00 0.10 max 9.00 – 12.00 5(C+N) – 0.70 max
SS 321H 0.04 – 0.10 2.0 max 1.0 max 0.045 max 0.030 max 17.00 – 19.00 0.10 max 9.00 – 12.00 4(C+N) – 0.70 max

Stainless Steel 321/321H Buttweld Fittings Mechanical Properties

Density Melting Point Tensile Strength Yield Strength (0.2%Offset) Elongation
8.0 g/cm3 1457 °C (2650 °F) Psi – 75000 , MPa – 515 Psi – 30000 , MPa – 205 35 %

Equivalent Grades for 321/321H Stainless Steel Pipe Fitting

STANDARD WERKSTOFF NR. UNS JIS EN
SS 321 1.4541 S32100 SUS 321 X6CrNiTi18-10
SS 321H 1.4878 S32109 SUS 321H X12CrNiTi18-9

SS 321/321H Buttweld Pipe Fittings Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Stainless Steel 321/321H Buttweld Fitting Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2023-12-29T12:37:36+05:30July 27th, 2021|

Stainless Steel 317 Buttweld Fittings Manufacturer In India

Sachiya Steel International is one of the Leading Manufacture And Exporter of high quality Stainless Steel 317 Buttweld Fittings, which has excellent general corrosion resistance and is superior in most environments. Stainless Steel 317 Elbow Butt Weld Pipe Fittings has excellent resistance to localized corrosion including inter – granular, pitting and crevice corrosion, where the CPT is generally at least 35 Degree C. Stainless Steel 317 Reducer is also resistant to chloride stress corrosion cracking (SCC) at temperatures of up to about 150 Degree C.

Stainless Steel 317 Tee Butt Weld Pipe Fittings will often perform well in environments which cause premature failure of austenitic grades. Stainless Steel 317 Cross Butt Weld Pipe Fittings has better resistance to sea water than grade 316. Although stainless steel has good high temperature oxidation resistance, Stainless Steel 317 Bend Butt Weld Pipe Fittings suffer from embrittlement if held for even short times at temperatures above 270 Degree C. If embrittled, Stainless Steel 317 Stub End can only be rectified by a full solution annealing treatment.

Because of its high strength, Stainless Steel 317 End Cap performs well in abrasion/corrosion conditions. A PRE guaranteed to be at least 40 indicates that Stainless Steel 317 Dish Cap Butt Weld Pipe Fittings has good pitting and crevice corrosion resistance to warm sea water and other high chloride environments.

Stainless Steel 317 Pipe Fittings Specifications
Specifications : ASTM A403 / ASME SA403
Size : 1/8” NB TO 48” NB. (Seamless & 100% X-Ray Welded, Fabricated)
Standards
 : ASME/ANSI B16.9, ASME B16.28, MSS-SP-43
Thickness : 5s, 10s, 40s, 80s, 10, 20, 40, STD, 60, 80, XS, 100, 120, 140, 160, XXS available with NACE MR 01-75
Type : Seamless / Welded / Fabricated

SS 317 Pipe Fittings Chemical Composition

Grade C Ni Mn P S Cr Si Mo Fe
317 0.08 max 11.00 – 15.00 2 max 0.045 max 0.030 max 18.00 – 20.00 1 max 3.00 – 4.00 57.845 min

Stainless Steel 317 Butt weld Fittings Mechanical Properties

Density Melting Point Tensile Strength Yield Strength (0.2%Offset) Elongation
7.9 g/cm3 1400 °C (2550 °F) Psi – 75000 , MPa – 515 Psi – 30000 , MPa – 205 35 %

Equivalent Grades for 317 Stainless Steel Pipe Fitting

STANDARD WERKSTOFF NR. UNS JIS BS GOST AFNOR EN
317  1.4449 S31700     SUS 317      –             –                –           –

SS WERKSTOFF NR.1.4449 Buttweld Pipe Fittings Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Stainless Steel 317 Buttweld Fitting Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2024-01-04T15:15:45+05:30July 26th, 2021|

Stainless Steel 316Ti Buttweld Fittings Manufactures In India

Sachiya Steel International is one of the Leading Manufacture And Exporter of Stainless Steel 316TI Buttweld Fittings, which retains physical and mechanical properties similar to standard grades of 316. The main advantage of Stainless Steel 316Ti Elbow Butt Weld Pipe Fittings is that it can be held at higher temperatures for a longer period without sensitization (precipitation) occurring. Stainless Steel 316Ti Reducer has good resistance to oxidation in intermittent service to 870 Degree C and in continuous service to 925 Degree C.

However, continuous use at 425 Degree C – 860 Degree C is not recommended in Stainless Steel 316Ti Tee Butt Weld Pipe Fittings if corrosion resistance in water is required. Stainless Steel 316Ti Cross Butt Weld Pipe Fittings cannot be hardened by heat treatment. Solution treatment or annealing in Stainless Steel 316Ti Bends Butt Weld Pipe Fittings can be done by rapid cooling after heating to 1010 Degree C – 1120 Degree C. In this instance, Stainless Steel 316Ti Stub End is recommended due to its resistance to carbide precipitation. Where high strength is required at temperatures above 500 Degree C, Stainless Steel 316Ti End Cap is recommended.

Stainless Steel 316Ti Dish Cap Butt Weld Pipe Fittings is readily brake or roll formed into a variety of parts. Stainless Steel 316Ti Lateral Tee Butt Weld Pipe Fittings is also suited to stamping, heading and drawing but post work annealing is recommended to relieve internal stresses.

Stainless Steel 316TI Pipe Fittings Specifications
Specifications : ASTM A403 / ASME SA403
Size : 1/8” NB TO 48” NB. (Seamless & 100% X-Ray Welded, Fabricated)
Standards
 : ASME/ANSI B16.9, ASME B16.28, MSS-SP-43
Thickness : 5s, 10s, 40s, 80s, 10, 20, 40, STD, 60, 80, XS, 100, 120, 140, 160, XXS available with NACE MR 01-75
Type : Seamless / Welded / Fabricated

SS 316TI Pipe Fittings Chemical Composition

Grade C Ni Mn P S Cr Si Mo N
316TI 0.08 max 10.00 – 14.00 2.0 max 0.045 max 0.030 max 16.00 – 18.00 0.75 max 2.00 – 3.00 –

Stainless Steel 316TI Butt weld Fittings Mechanical Properties

Density Melting Point Tensile Strength Yield Strength (0.2%Offset) Elongation
8.0 g/cm3 1399°C (2550°F) Psi – 75000 , MPa – 515 Psi – 30000 , MPa – 205 35 %

Equivalent Grades for 316TI Stainless Steel Pipe Fitting

STANDARD WERKSTOFF NR. UNS JIS BS GOST AFNOR EN
316TI 1.4571 s31703 SUS 316Ti      320S31    08Ch17N13M2T   Z6CNDT17‐123 X6CrNiMoTi17-12-2

SS WERKSTOFF NR.1.4571 Buttweld Pipe Fittings Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Stainless Steel 316TI Buttweld Fitting Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2024-01-04T16:54:41+05:30July 26th, 2021|

Stainless Steel 310H Buttweld Fittings Manufacturer In India

Sachiya Steel International is one of the Leading Manufacture And Exporter of high quality Stainless Steel 310H Buttweld Fittings, which is stable under standard conditions can be subjected to pressures before transforming into a high – pressure form, as described in the next section. Because of its significance for planetary cores, the physical properties of these Stainless Steel 310H Elbow at high pressures and temperatures have also been studied extensively. As molten stainless steel cools past its freezing point of 1538 Degree C, Stainless Steel 310H Tee Butt Weld Pipe Fittings crystallizes into its allotrope, which has a body – centered cubic (bcc) crystal structure.

Stainless Steel 310H Buttweld Fittings

As it cools further to 1394 Degree C, these Stainless Steel 310H Cross Butt Weld Pipe Fittings changes to its gamma-steel allotrope, a face – centered cubic (fcc) crystal structure, or austenite. At 912 Degree C and below, the crystal structure of Stainless Steel 310H Reducer again becomes the bcc alpha – steel allotrope, or ferrite. Finally at 770 Degree C, these Stainless Steel 310H Bend Butt Weld Pipe Fittings forms magnetic and also changes from paramagnetic to ferromagnetic.

As Stainless Steel 310H Stub End, passes through the Curie temperature there is no change in crystalline structure, but there is a change in “domain structure”, where each domain contains iron atoms with a particular electronic spin.

Stainless Steel 310H Pipe Fittings Specifications
Specifications : ASTM A403 / ASME SA403
Size : 1/8” NB TO 48” NB. (Seamless & 100% X-Ray Welded, Fabricated)
Standards
 : ASME/ANSI B16.9, ASME B16.28, MSS-SP-43
Thickness : 5s, 10s, 40s, 80s, 10, 20, 40, STD, 60, 80, XS, 100, 120, 140, 160, XXS available with NACE MR 01-75
Type : Seamless / Welded / Fabricated

SS 310H Pipe Fittings Chemical Composition

Grade C Mn Si P S Cr Mo Ni N
SS 310H 0.04 – 0.10 2 max 1.00 max 0.045 max 0.030 max 24.00 – 26.00 – 19.00 – 21.00 53.885 min

Stainless Steel 310H Buttweld Fittings Mechanical Properties

Density Melting Point Tensile Strength Yield Strength (0.2%Offset) Elongation
7.9 g/cm3 1402 °C (2555 °F) Psi – 75000 , MPa – 515 Psi – 30000 , MPa – 205 40%

Equivalent Grades for 310H Stainless Steel Pipe Fitting

STANDARD WERKSTOFF NR. UNS JIS BS GOST AFNOR EN
SS 310H – S31009 – – – – –

SS 310H Buttweld Pipe Fittings Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Stainless Steel 310H Buttweld Fitting Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2024-02-06T19:06:29+05:30July 24th, 2021|Buttweld Fittings|

Stainless Steel 316 Buttweld Fittings Manufacturers In India

Stainless Steel 316 Buttweld Fittings Manufacturers In India

Sachiya Steel International is one of the Leading Manufacture And Exporter for Stainless Steel 316 Buttweld Fittings, which is being offered in different sizes and shapes to our clients. In addition to having an excellent track record for recyclability and end of life recapture rates, our Stainless Steel 316 Elbow also meets another important criterion of a sustainable material. If the right stainless steel is selected to match the corrosion conditions of the environment, these Stainless Steel 316 Tee Pipe Fittings can typically meet the lifetime needs of a project.

While other materials may lose effectiveness over time, our Stainless Steel 316 Cross Pipe Fittings can retain both functionality and appearance over extended lengths of time. It has been exposed to heavy pollution for most its existence, has had very minimal cleaning, and yet these Stainless Steel 316 Reducer is still considered to be in excellent condition.

Stainless Steel 316 Buttweld Fittings

Although our Stainless Steel 316 Bend Pipe Fittings has only been in production for many years, and so theoretically stainless steel should be able to last centuries when properly selected. These Stainless Steel 316 Stub End is particularly exciting to consider that some of the same factors that contribute to making stainless steel an excellent environmental choice, can also lead to making it an excellent economical choice, especially when considering the lifetime costs of a project.

Stainless Steel SS 316/316L Pipe Fittings Specifications
Specifications : ASTM A403 / ASME SA403
Size : 1/8” NB TO 48” NB. (Seamless & 100% X-Ray Welded, Fabricated)
Standards
 : ASME/ANSI B16.9, ASME B16.28, MSS-SP-43
Thickness : 5s, 10s, 40s, 80s, 10, 20, 40, STD, 60, 80, XS, 100, 120, 140, 160, XXS available with NACE MR 01-75
Type : Seamless / Welded / Fabricated

SS 316/316L Pipe Fittings Chemical Composition

Grade C Mn Si P S Cr Mo Ni N
316 min. – – – – 16.0 2.0-3.0 10.0 –
max. 0.035 2.0 0.75 0.045 0.030 18.0 14.0 –
316L min. – – – – – 16.0 2.0-3.0 10.0 –
max. 0.035 2.0 0.75 0.045 0.030 18.0 14.0 –

Stainless Steel 316/316L Buttweld Fittings Mechanical Properties

Grade Tensile Strength (MPa) min Yield Strength 0.2% Proof (MPa) min Elongation (% in 50mm) min Hardness
Rockwell B (HR B) max Brinell (HB) max
316 515 205 40 95 217
316L 485 170 40 95 217

Equivalent Grades for 316 / 316L Stainless Steel Pipe Fitting

STANDARD WERKSTOFF NR. UNS JIS BS GOST AFNOR EN
SS 316 1.4401 / 1.4436 S31600 SUS 316 316S31 / 316S33 – Z7CND17‐11‐02 X5CrNiMo17-12-2 / X3CrNiMo17-13-3
SS 316L 1.4404 / 1.4435 S31603 SUS 316L 316S11 / 316S13 03Ch17N14M3 / 03Ch17N14M2 Z3CND17‐11‐02 / Z3CND18‐14‐03 X2CrNiMo17-12-2 / X2CrNiMo18-14-3

SS 316/316L Buttweld Pipe Fittings Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Stainless Steel 316/316L Buttweld Fitting Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

 

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2024-02-06T19:18:53+05:30July 24th, 2021|Buttweld Fittings|

Stainless Steel 310 Buttweld Fittings Manufacturer In India

Stainless Steel 310 Buttweld Fittings Manufacturer In India

Sachiya Steel International is one of the well-known Manufacture And Exporter for high quality Stainless Steel 310 Buttweld Fittings , which is used widely in the construction of roads, railways, other infrastructure, appliances, and buildings. Stainless Steel 310 Elbow Butt Weld Pipe Fittings is also used for most large modern structures, such as stadiums and skyscrapers, bridges, and airports. Even those with a concrete structure employ Stainless Steel 310S Tee Butt Weld Pipe Fittings for reinforcing, where in addition it sees widespread use in major appliances and cars.

Stainless Steel 310 Buttweld Fittings

Stainless Steel 310 Reducer is a mixture of several metals (this is called an alloy) but most of it is iron, which is harder and stronger than iron. Stainless Steel 310S Cross Butt Weld Pipe Fittings are often iron alloys with between 0.02 % and 1.7 % percent carbon by weight. Stainless Steel 310 Bend Butt Weld Pipe Fittings with more carbon than this are known as cast iron, in which carbon is replaced with other alloying materials.

Stainless Steel 310S Stub End is different from wrought iron that has little or no carbon, where variations and combinations of production routes also exist. Stainless Steel 310 End Cap Butt Weld Pipe Fittings is an alloy of iron and carbon containing less than 2 % carbon and 1 % manganese and small amounts of silicon, phosphorus, Sulphur and oxygen.

Stainless Steel SS 310 / 310S Pipe Fittings Specifications
Specifications : ASTM A403 / ASME SA403
Size : 1/8” NB TO 48” NB. (Seamless & 100% X-Ray Welded, Fabricated)
Standards
 : ASME/ANSI B16.9, ASME B16.28, MSS-SP-43
Thickness : 5s, 10s, 40s, 80s, 10, 20, 40, STD, 60, 80, XS, 100, 120, 140, 160, XXS available with NACE MR 01-75
Type : Seamless / Welded / Fabricated

SS 310 / 310S Pipe Fittings Chemical Composition

Grade C Mn Si P S Cr Mo Ni N
SS 310 0.015 max 2 max 0.015 max 0.020 max 0.015 max 24.00 – 26.00 0.10 max 19.00 – 21.00 54.7 min
SS 310S 0.08 max 2 max 1.00 max 0.045 max 0.030 max 24.00 – 26.00 0.75 max 19.00 – 21.00 53.095 min

Stainless Steel 310 / 310S Buttweld Fittings Mechanical Properties

Density Melting Point Tensile Strength Yield Strength (0.2%Offset) Elongation
7.9 g/cm3 1402 °C (2555 °F) Psi – 75000 , MPa – 515 Psi – 30000 , MPa – 205 40 %

Equivalent Grades for 310 / 310S Stainless Steel Pipe Fitting

STANDARD WERKSTOFF NR. UNS JIS BS GOST AFNOR EN
SS 310 1.4841 S31000 SUS 310 310S24 20Ch25N20S2 – X15CrNi25-20
SS 310S 1.4845 S31008 SUS 310S 310S16 20Ch23N18 – X8CrNi25-21

SS 310 / 310S Buttweld Pipe Fittings Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Stainless Steel 310 / 310S Buttweld Fitting Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

 

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2024-02-07T13:30:24+05:30July 23rd, 2021|Buttweld Fittings|

Stainless Steel 304H Buttweld Fittings Manufacturer In India

Sachiya Steel International is one of the Leading Manufacture And Exporter of Stainless Steel 304H Buttweld Fittings, which is unaffected by any of the weak bases such as ammonium hydroxide, even in high concentrations and at high temperatures. Stainless Steel 304H Elbow is generally highly resistant to attack from acids, but this quality depends on the kind and concentration of the acid, the surrounding temperature, and the type of steel. Stainless Steel 304H Tee Pipe Fittings is exposed to stronger bases such as sodium hydroxide at high concentrations and high temperatures will likely experience some etching and cracking, especially with solutions containing chlorides such as sodium hypochlorite.

Stainless Steel 304H Cross Pipe Fittings are useful for storing and handling acetic acid, especially in solutions where it is combined with formic acid and when aeration is not present (oxygen helps protect stainless steel under such conditions). Stainless Steel 304H Reducer is also commonly used with formic acid though it will tend to discolor the solution, which further resist damage from aldehydes and amines.

Stainless Steel 304H Buttweld Fittings

Fats and fatty acids only affect Stainless Steel 304H Stub End Pipe Fittings at temperatures above 150 Degree C (302 Degree F), and above is unaffected at all temperatures. Stainless Steel 304H Pipe Bend is required for processing of urea, which is a relatively poor conductor of electricity, with significantly lower electrical conductivity than copper.

Stainless Steel 304H Pipe Fittings Specifications
Specifications : ASTM A403 / ASME SA403
Size : 1/8” NB TO 48” NB. (Seamless & 100% X-Ray Welded, Fabricated)
Standards
 : ASME/ANSI B16.9, ASME B16.28, MSS-SP-43
Thickness : 5s, 10s, 40s, 80s, 10, 20, 40, STD, 60, 80, XS, 100, 120, 140, 160, XXS available with NACE MR 01-75
Type : Seamless / Welded / Fabricated

SS 304H Pipe Fittings Chemical Composition

Grade C Mn Si P S Cr Mo Ni N
304H min. 0.04 – – – – 18.0 – 8.0 –
max. 0.010 2.0 0.75 0.045 0.030 20.0 10.5 –

Stainless Steel 304H Buttweld Fittings Mechanical Properties

Grade Tensile Strength (MPa) min Yield Strength 0.2% Proof (MPa) min Elongation (% in 50mm) min Hardness
Rockwell B (HR B) max Brinell (HB) max
304H 515 205 40 92 201

Equivalent Grades for 304H Stainless Steel Pipe Fitting

Grade UNS No Old British Euronorm Swedish SS Japanese JIS
BS En No Name
304H  S30409 – – 1.4301 – – –

SS 304H Buttweld Pipe Fittings Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Stainless Steel 304H Buttweld Fitting Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2024-02-07T13:33:59+05:30July 23rd, 2021|Buttweld Fittings|

Stainless Steel 304L Buttweld Fittings Manufacturer In India

Stainless Steel 304L Buttweld Fittings Manufacturer In India

Sachiya Steel International is one of the Leading Manufacture And Exporter of Stainless Steel 304L Buttweld Fittings, which can get marked up by fingerprints and grease, develop discoloration, and eventually rust. Stainless Steel 304L Pipe Fittings is austenitic steel possessing a minimum of 18 % chromium and 8 % nickel, combined with a maximum of 0.08 % carbon. Stainless Steel 304L Elbow is nonmagnetic steel which cannot be hardened by heat treatment, but instead must be cold worked to obtain higher tensile strengths.

As a result, Stainless Steel 304L Tee Pipe Fittings can be used in as – welded condition, even in severe corrosive conditions. Stainless Steel 304L Reducer often eliminates the necessity of annealing weldments except for applications specifying stress relief. Stainless Steel 304L Long Stub End Pipe Fittings has slightly lower mechanical properties than Type 304. Stainless Steel 304L End Cap Pipe Fittings is non – harden able by heat treatment, where annealing of heat is done up to 1900 Degree F – 2050 Degree F (1038 Degree C – 1121 Degree C), then cool rapidly.

Thin strip sections of Stainless Steel 304L Dish Cap Pipe Fittings may be air cooled, but heavy sections should be water quenched to minimize exposure in the carbide precipitation region. Stainless Steel 304L Short Stub End Pipe Fittings has very good drawability, which can withstand much more time and abuse before showing signs of wear.

Stainless Steel 304L Buttweld Fittings

Stainless Steel 304L Pipe Fittings Specifications
Specifications : ASTM A403 / ASME SA403
Size : 1/8” NB TO 48” NB. (Seamless & 100% X-Ray Welded, Fabricated)
Standards
 : ASME/ANSI B16.9, ASME B16.28, MSS-SP-43
Thickness : 5s, 10s, 40s, 80s, 10, 20, 40, STD, 60, 80, XS, 100, 120, 140, 160, XXS available with NACE MR 01-75
Type : Seamless / Welded / Fabricated

SS 304L Pipe Fittings Chemical Composition

Grade C Mn Si P S Cr Mo Ni N
304L min. – – – – – 18.0 – 8.0 –
max. 0.030 2.0 0.75 0.045 0.030 20.0 12.0 0.10

Stainless Steel 304L Buttweld Fittings Mechanical Properties

Grade Tensile Strength (MPa) min Yield Strength 0.2% Proof (MPa) min Elongation (% in 50mm) min Hardness
Rockwell B (HR B) max Brinell (HB) max
304L 485 170 40 92 201

Equivalent Grades for 304L Stainless Steel Pipe Fitting

Grade UNS No Old British Euronorm Swedish SS Japanese JIS
BS En No Name
304L S30403 304S31 58E 1.4301 X5CrNi18-10 2332 SUS 304

SS 304L Buttweld Pipe Fittings Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Stainless Steel 304L Buttweld Fitting Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2024-04-05T19:24:53+05:30July 22nd, 2021|

Stainless Steel 304 Buttweld Fittings Manufacturer In India

Stainless Steel 304 Buttweld Fittings Manufacturer In India

Sachiya Steel International is one of the Leading Manufacture And Exporter of Stainless Steel 304 Buttweld Fittings, which is a molybdenum bearing austenitic stainless steel that provides improved corrosion resistance. These Stainless Steel 304 Tee Pipe Fittings is non – magnetic in the annealed condition but may become slightly magnetic as a result of welding. Stainless Steel 304 Stub End Pipe Fittings has excellent corrosion resistance in a wide range of chemicals, especially in acidic chloride environments such as those encountered in pulp and paper mills.

Increased levels of chromium, molybdenum and nickel in these Stainless Steel 304 End Cap, improve resistance to chloride pitting and general corrosion. Resistance of Stainless Steel 304 Dish Cap Pipe Fittings increases with molybdenum alloy content, which is further resistant to sulphuric acid concentrations up to 5 percent at temperatures as high as 120 Degree F (49 Degree C). At temperatures under 100 Degree F (38 Degree C), these Stainless Steel 304 Long Radius Elbow has excellent resistance to solutions of higher concentration.

However, service tests in Stainless Steel 304 Short Radius Elbow Pipe Fittings are recommended to account for the effects of specific operating conditions that may affect corrosion behavior. In processes where condensation of Sulphur – bearing gases occurs, these Stainless Steel 304 Elbow Pipe Fittings is much more resistant to attack at the point of condensation than conventional alloy 316.

Stainless Steel 304 Buttweld Fittings

Stainless Steel 304 Buttweld Fittings Specifications
Specifications : ASTM A403 / ASME SA403
Size : 1/8” NB TO 48” NB. (Seamless & 100% X-Ray Welded, Fabricated)
Standards
 : ASME/ANSI B16.9, ASME B16.28, MSS-SP-43
Thickness : 5s, 10s, 40s, 80s, 10, 20, 40, STD, 60, 80, XS, 100, 120, 140, 160, XXS available with NACE MR 01-75
Type : Seamless / Welded / Fabricated

SS 304 Pipe Fittings Chemical Composition

Grade C Mn Si P S Cr Mo Ni N
304 min. – – – – – 18.0 – 8.0 –
max. 0.08 2.0 0.75 0.045 0.030 20.0 10.5 0.10

Stainless Steel 304 Buttweld Fittings Mechanical Properties

Grade Tensile Strength (MPa) min Yield Strength 0.2% Proof (MPa) min Elongation (% in 50mm) min Hardness
Rockwell B (HR B) max Brinell (HB) max
304 515 205 40 92 201

Equivalent Grades for 304 Stainless Steel Pipe Fitting

Grade UNS No Old British Euronorm Swedish SS Japanese JIS
BS En No Name
304 S30400 304S31 58E 1.4301 X5CrNi18-10 2332 SUS 304

SS 304 Buttweld Pipe Fittings Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Stainless Steel 304 Buttweld Fitting Test Certificates

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.

Material Testing 

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

By |2024-04-08T15:24:23+05:30July 22nd, 2021|
LOGO 1200 X 300

D-2, Office No 3, Bharat Nagar CHS, Near Shalimar Cinema,
Grant Road ( East ) , Mumbai- 40007, Maharashtra, India.

[email protected]
[email protected]

OUR PRODUCTS

ACCREDITATION

certified stamp

© Copyright - 2024 | Sachiya Steel International | All Rights Reserved | Terms & Conditions | Privacy Policy | Sitemap

Go to Top